A to Z Rubber Stamps 01-07554-000170 Manual Download Page 39

Page: 39 / 122

Actuating Pawl Assembly:

-Note location of spacers on shaft for reinstallation.
-Push protruding end of shaft through swing and pull out flared end, removing shaft

completely from swing.

-Pull actuating pawl assembly free of swing.

Cam Follower:

-Use needle nose pliers to remove return spring.
-Remove 5/16 hex nut that secures cam follower shaft, and unscrew shaft.
-Pull cam follower free.

Changing A Unit Wheel:

NOTE

THE FOLLOWING PROCEDURE CAN BE USED TO CHANGE ANY

RAPIDPRINT TYPE WHEEL. REMEMBER, IT IS IMPORTANT TO CAREFULLY
REINST ALL SPACERS TO MAINTAIN ORIGINAL WHEEL SPACING

-UNPLUG MACHINE FROM WALL OUTLET.
-Disconnect motor leads and remove the typesection assembly. Also, remove die

plates, if any. Note location of spacing paper between frame and die plate.

-Remove connecting arm.
-Disconnect all retaining pawl springs (noting location for reassembly).
-Loosen the wheel shaft locking screw and slide the retainer free.
-Use an extra wheel shaft and push the existing one through the side of the frame

opposite

the retainer (

figure 20

01/04/2012

Summary of Contents for 01-07554-000170



























































































































Search results

Summary of Contents for 01-07554-000170

Reviews:

Brands by name

Popular brands

A to Z Rubber Stamps 01-07554-000170, Manual

Search results

Summary of Contents for 01-07554-000170

Reviews:

Brands by name

Popular brands