background image

6

English

DMP1616 / DMP1616D

PIN

FUNCTION

POSITION

DESCRIPTION

1

Firmware Upgrade

ON

Firmware Upgrade Mode

OFF

Operation Mode

2

IP address setting method

ON

By Hardware

OFF

By Software

3

Leading digit of host digit of IP address

ON

Please consult “How to Set Unit IP”

section of this manual.

OFF

4

Second digit of host digit of IP address

ON

OFF

7

Resume factory default settings

ON

Resume factory default settings

OFF

Operation Mode

DMP1616 DIP SWITCH SETTINGS

upper position: ON

Iower position: OFF

The Dante expansion card should come pre-installed with 

the DMP1616D (and is not included with the DMP1616). 

This is an optional component that is not included on all 

versions of the DMP1616.

The “Primary” port  on the Dante card can be connected to 

your network router. The Secondary port can be connected 

to the Primary port of additional units. Alternatively, all 

units can be connected to the router using their “Primary” 

ports. 

The  Audinate  Dante  Controller  can  be  downloaded 

through their website (www.audinate.com). This is used to 

route the network signals from numerous Dante-enabled 

devices. Each device will show up as its own independent 

signal with input and output channels listed. All units will 

be automatically discovered by the software. 
Signals  can  be  routed  internally  using  the  instructions 

found in section 5. The actual network input signals 

received  by  your  DMP1616s  are  determined  by  the 

aforementioned  Dante  Controller  software.  It  should  be 

noted that each Network input mix can only have a single 

source assigned to it. 
Connecting additional units to your network will 

automatically be recognized by the software, allowing any 

of these systems to have their signals routed throughout 

the network. 
In addition to the regular network routing of signals, the 

Dante  expansion  cards  are  compatible  with  Audinate’s 

DANTE CONNECTIVITY 

(DMP1616D ONLY)

Virtual Soundcard software which allows for recording 

of audio to the computer and playback of audio from the 

computer.  At  the  time  of  publication,  this  a  permanent 

license  for  this  software  is  available  for  $29.99  through 

Audinate’s website. 

The controller software is completely free on Windows 

7 (SP1), Windows 8.1, Windows 10, OSX 10.10.5 

(Yosemite), OSX 10.11.6 (El Capitan), macOS 10.12 

(Sierra) and macOS 10.13 (High Sierra). 

Summary of Contents for DMP1616





























Reviews: