background image

7

FlAMe SeNSor

Each  burner  is  equipped  with  a  flame  sensor  to  detect  the 

presence of the burner flames at high and low fire conditions. If 

no flame is sensed, the gas valve will close automatically. The 

voltage sensed by the flame sensor will also be displayed on the 

Burner Screen.

FiGUre 6.  FlAMe SeNSor

WATer TeMperATUre liMiT CoNTrolS

The “XB/XW” models incorporate an outlet water sensor having 

dual sensors, that are factory set at 210°F (99°C).

MAiN poWer SUpplY SWiTCh

The main power supply switch is a padlockable switch. This switch 

pro vides 120V from the power supply to the boiler.

This switch needs to be turned off when servicing the boiler.
NoTe: The enable/Disable Switch on the front of the boiler 

does not interrupt electrical power to the boiler.

FiGUre 7.  MAiN poWer SUpplY SWiTCh

WATer TeMperATUre SeNSorS

FiGUre 8.  WATer TeMperATUre SeNSorS

Temperature  sensors  are  threaded  immersion  probes. 

Temperature  probes  have  embedded  temperature  sensors 

(thermistors). The boiler’s control system monitors these sensors 

to determine water temperature at various points in the system. 

iNleT AND oUTleT TeMperATUre SeNSorS

All  models  have  two  inlet  and  two  outlet  temperature  sensors 

for each heat exchanger, factory installed to monitor the water 

temperature entering and leaving the boiler. The Inlet Probe is 

a temperature sensor only and has two leads. The Outlet Probe 

also  contains  the  manual  reset  high  temperature  limit  switch 

and  has  four  leads. The  control  system  displays  the  Inlet  and 

Outlet water temperatures sensed from these two sensors on the 

default Temperatures screen.

reMoTe SeNSorS

All models are supplied from the factory with a remote sensor. 

The remote sensor is used to control system water temperature 

for a single boiler in a domestic hot water storage tank or in the 

return line from a primary/secondary hydronic heating system.
The  boiler  will  modulate  its  firing  rate  in  response  to  the 

actual  system  temperature  and  load  conditions.  The  control 

 

system displays the temperature sensed from the remote sensor  

as the “Lead Lag” temperature on the default Temperatures screen.

loW WATer CUToFF DeViCe (lWCo)

Low water cutoff device is normally a closed switch that opens 

when water drops below a preset level. Each model is equipped 

with a factory installed LWCO. LWCO board is connected to the 

electronic panel, whereas the sensor probe is connected to the 

heat exchanger.

FiGUre 9.  lWCo boArD AND probe

Summary of Contents for XB-1000



















































Reviews: