background image

16

REPAIR PARTS

REPAIR PARTS SCHEDULE

ORDERING 

REPAIR 

PARTS 

           

The following parts may be ordered through the store you purchased the solar water heater from, or direct from the factory listed on 

the model & rating plate located on the lower front of the solar water heater.  Selling prices will be furnished on request or parts will 

be shipped at prevailing prices and you will be billed accordingly.  When ordering repair parts always give the following information:  

(1) Part description, (2) Model serial number, (3) Element wattage, (4) Voltage, (5) Part number.

ITEM

PART DESCRIPTION

SERVICE 

PART #

1

Primary Anode

9003892005

2

Anode Outlet

9006827005

3

Primary Dip Tube

9002549005

4

Element w/Gasket

9003950115

5

Thermostat Bracket

9003898215

6

Thermostat w/High Limit

9007623015

7

Terminal Cover

9003914015

8

Access Panel

9003900005

9

Sensor Mounting Plug

9007309005

10

Solar Loop Dip Tube (From Collector)

9006789005

11

Solar Loop Dip Tube w/Nipple (To Pump)

9006790005

12

Plastisert Nipple

9003976015

13

T&P Valve

9000728015

14

Drain Valve

9003906015

RATING PLATE

A rating plate identifying the solar water heater will be found above the drain valve.  When referring to the solar water heater, always 

have the information listed on the rating plate readily available.
Fill in that information here:

MODEL NO. _______________________________________  

SERIAL NO. _______________________________________  

INSTALLATION DATE:

 _______________________________

Summary of Contents for Cirrex SUN-80





















Reviews: