100299634_2000545244_ Rev. A
43
LIGHTING INSTRUCTIONS
Read and understand these directions thoroughly before
attempting to operate the water heater. Make sure the
burner viewport is not missing or damaged. Make sure
the tank is completely filled with water before operating
the water heater. The gas control valve/thermostat has an
“On/Off Switch” and must be turned on before the water
heater is operational. Check the label on the front of the
water heater near the gas control valve/thermostat for
the correct gas. Do not start this water heater with any
gas other than the one listed on the label. If you have any
questions or doubts, consult the gas supplier or gas utility
company. The following Lighting Instruction label appears
on the front of the water heater.
This heater is equipped with a Honeywell gas control/
thermostat and a hot-surface igniter. This control is a
combination gas valve, thermostat and ignition controller
for use on this power vented water heater. The valve
contains a micro-controller that supervises the ignition
sequence and monitors the temperature settings and
operation of the heater. The controller also monitors the
flammable vapor safety features of this heater.
This heater is equipped with a hot-surface ignition
system that automatically ignites the burner. Do not
attempt to light this heater manually with a match or
flame-producing device.
323546-000
1. Turn the thermostat counter-clockwise to the lowest setting.
2. Set the gas control switch to the “OFF” position.
3. Turn off electrical power to the appliance if service is to be performed.
TO TURN OFF GAS TO APPLIANCE
1.
STOP! Read the safety
information above on this
label.
2. Turn off all electric power to the
appliance.
3. Turn the thermostat
counter-clockwise to the
lowest setting.
4. Set the switch on the control to
the “OFF” position.
5. Do not attempt to light manually.
6. Wait five (5) minutes to clear out
any gas. If you then smell gas, STOP!
Follow “B” in the safety information above on
this label. If you don't smell gas, go the next
step.
7. Turn on all electric power to
the appliance.
8. Set the switch on the control
to the “ON” position.
9. Turn thermostat to desired
setting.
DANGER
Hotter water
increases the risk of
scald injury. Consult the
instruction manual before
changing temperature.
10. If the appliance will not operate, follow the
instructions “To Turn Off Gas To Appliance”
and call your service technician or gas
supplier.
OPERATING INSTRUCTIONS
DANGER
A. This appliance does not have a pilot. It is
equipped with an ignition device which
automatically lights the burner.
Do NOT try
to light the burner by hand.
B. BEFORE OPERATING smell all around the
appliance area for gas. Be sure to smell next
to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electric switch; Do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppliers
instructions.
• If you cannot reach your gas supplier, call the
fire department.
C. Use only your hand to turn the gas control
buttons. Never use tools. If the control
buttons will not turn, don't try to repair them,
call a qualified service technician. Force or
attempted repair may result in a fire or
explosion.
D. Do not use this appliance if any part has
been under water. Immediately contact a
qualified installer or service agency to
replace a flooded water heater. Do not
attempt to repair the unit. It must be
replaced!
BEFORE OPERATING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES.
FLAMMABLE
FLAMMABLE
WARNING
: If you do not follow these instructions exactly, a fire
or explosion may result causing property damage, personal
injury or loss of life.
FOR YOUR SAFETY READ BEFORE LIGHTING
