909 DYM-1773 Instruction Manual Download Page 12

12

9.2 Cutting blade

CAUTION:

 Be sure to disconnect and ground the spark 

plug wire before working on the cutting blade to prevent 

accidental engine starting. Protect hands by using heavy 

gloves or a rag to grasp the cutting blades .lip mower as 

specified in separate engine manual. Remove the hex bolt 

and washer which hold the blade and blade adapter to the 

engine crankshaft. Remove the blade and adapter from the 

crankshaft.

WARNING:

 Periodically inspect the blade adapter for 

cracks, especially if you strike a foreign object. Replace 

when necessary. For best results your blade should be 

sharp. The blade may be resharpened by removing it and 

either grinding or filing the cutting edge keeping as close to 

the original bevel as possible. It is extremely important that 

each cutting edge receives an equal amount of grinding to 

prevent an unbalanced blade. Improper blade balance will 

result in excessive vibration causing eventual damage to 

the engine and mower. Be sure to carefully balance blade 

after sharpening. The blade can be tested for balance by 

balancing it on a round shaft. saewdriver. Remove metal 

from the heavy side until it balances evenly. 
Before reassembling the blade and the blade adapter to the 

unit, lubricate the engine crankshaft and the inner surface of 

the blade adapter with light oil. Install the blade adapter on 

the crankshaft. Refer to figure 13. Place the blade with the 

part number facing away from the adapter.
Align the washer over the blade and insert the hex bolt. 

lighten the hex bolt to the torque listed below:

9.3 Blade mounting torque

Center Bolt 40Nm-50Nm. to insure safe operation of your 

unit. ALL nuts and bolts must be checked periodically for 

correct tightness.
After prolonged use, especially in sandy soil conditions, 

the blade will become worn and lose some of the original 

shape. Cutting efficiently will be reduced and the blade 

should be replaced. Replaca with an approved factory 

replacement blade only. Possible damage resuffing from 

blade unbalance condition is not the responsibility of the 

manufacturer.
When you change the blade, Must use the original type 

marked on the blade (26300100401 for DYM1773); (for 

order the blade, pis. contact your local dealer or call our 

company)

9.4 Engine

Refer to the separate engine manual for engine 

maintenance instructions. Maintain engine oil as instructed 

in the separate engine manual packed with your unit. Read 

and follow instructions carefully.
Service air cleaner as per separate engine manual under 

normal conditions.
Clean every few hours under extremely dusty conditions. 

Poor engine performance and flooding usually indicates that 

the air cleaner should be serviced.
To service the air cleaner, refer to the separate engine 

manual packed with your unit.
The spark. plug should be cleaned and the gap reset once 

a season. Spark plug replacement is recommended at the 

start of each mowing season; check engine manual for 

correct plug type and gap specifications.
Clean the engine regularly with a cloth or brush. Keep the 

cooling system (blower housing area) clean to permit proper 

air circulation which is essential to engine performance and 

life. Be certain to remove all grass, dirt and combustible 

debris from muffler area.

Flat Key
Blade Adapter

Blade

Washer
Hex Bolt

Summary of Contents for DYM-1773

















Reviews: