background image

6

  Do not operate the machine near people, especially 

children or pets. Turn it off if they get too close. Maintain 

a safe distance of at least 5m from other people when 

using the machine.

  Keep a balanced and stable stance while using the 

machine.

  Ensure that the area being cut is free from strings, stones 

and debris.

  Do not cut against hard objects. This could cause injury 

to the operator and damage to the machine.

   Never use the machine without the guard. Never use the 

machine if the guard is damaged. 

WARNING: 

The guard is vital for your and other people’s 

safety and for the machine’s operating efficiency.

 

Do not try to stop the cutting device (nylon line) with your 

hands. Always let it come to a stop by itself. 

WARNING:

 After switching off the machine, the cutting 

device continues to rotate for a few more seconds. 

 

 Only use the original type of nylon line. Under no 

circumstances use metal line instead of nylon. 

 

Do not use the machine to cut grass which is not on the 

ground. For example, do not cut grass which is on walls 

or rocks.

 

 Do not switch on the machine in enclosed or poorly 

ventilated spaces or in the presence of inflammable and/

or explosive substances such as liquids, gasses and 

powders. 

 

Only cut during broad daylight or with adequate artificial 

light. 

 

 Check that all grass cuttings and dirt have been removed 

from the ventilation vents.

 

 Do not cross roads or gravel paths with the machine still 

running. 

 

When the machine is not in use, store it in a dry place 

and out of reach of children. 

 

After use, remove the battery pack from the trimmer and 

check the trimmer for damage. If you have the slightest 

doubts, contact an authorised service centre. 

 

 Only use the machine according to the instructions given 

in this manual. 

 

Check regularly that the screws are tight.

 

Do not try to repair the machine or access internal parts. 

Contact authorised service centres only. 

 

 Do not get distracted and always concentrate on what 

you are doing. Use common sense. Never operate the 

machine when you are tired, sick or under the influence 

of alcohol or other drugs.

Wear goggles 

Wear ear defenders 

Wear a breathing mask

Additional safety rules for the charger

   Your 909 tool with Lithium-Ion batteries may only be 

charged with the specific designed 909 Lithium-Ion 

battery charger purchased with the tool. 

IT IS 

DANGEROUS TO USE ANY OTHER BATTERY 

CHARGER TO CHARGE YOUR TOOL.

 Do not attempt 

to charge the battery pack with any other charger than 

the one supplied.

   If there is a problem with the battery or the tool, take 

it to your nearest Authorised Service centre or phone 

and speak with an experienced 909 Customer Service 

Representative for assistance in rectifying your problem.

   Before using the charger, read all the instructions, labels 

and cautionary markings on the charger and battery pack 

as well as the instructions on using the battery pack.

   Do not use the charger if it has been subjected to a 

heavy knock, dropped or otherwise damaged in any way. 

Take the charger to an authorised service centre for a 

check or repair.

Summary of Contents for 20VLTG





















Reviews: