background image

7

Introduction

Congratulations on purchasing your new 909 Aluminium 

LED rechargeable Flashlight.
Ensure to read this instruction manual and follow the 

instructions carefully prior to using the product.

Fitting and removing the flashlight  

from the charging stand adaptor

•  To fit the flashlight, insert the lower end of the handle 

flashlight into the round recess in the bottom of the 

charging stand. The flashlight will be on an angle. When 

inserted, push the body of the flashlight into the two 

upper wings of the charging stand adaptor. These wings 

are spring loaded and will allow the flashlight to fully enter 

and locate in the housing.

•  To remove the flashlight, pull the upper section of the 

flashlight outward. The wings will release the flashlight. 

Then lift the flashlight out of the lower recess.

Charging / recharging the flashlight

This flashlight is shipped in a partially charged state and will 

require charging.
Charge the Lithium-Ion model No 10309L for approx 6-8 

hours, or the NiMH model No 10307 for approx 5-7 hours.
•  Ensure the flashlight is turned off
•  Fit the flashlight into the charging stand adaptor, ensuring 

the flashlight fully clips into place. 

•  Connect the plug of the plug pack charger into the 

charging port of the charging stand.

•  Connect the plug pack charger into a house hold 240Vac 

power point and turn on.

•  Check the charging indicator on the charging stand 

adaptor. The indicator should be glowing red, indicating 

the charging process is underway.

•  When the flashlight is fully charged the Red indicator will 

change to Green.

•  Turn Off the 240Vac plug pack adaptor and remove the 

plug pack from the power point.

To turn the flashlight On and Off

•  To turn the flashlight ON, press the “push button switch”.
•  To turn the flashlight Off, press again the “push button 

switch”.

Care and maintenance

All batteries lose energy from self-discharge over time and 

more rapidly at higher temperatures. When the unit is not 

in use, we recommend that the battery is charged at least 

every 120 days.
Never submerge the unit in water. If the unit gets dirty, 

gently clean the outer surfaces of the spotlight unit with 

a soft cloth moistened with a mild solution of water and 

detergent.
There are no user-replaceable parts. Periodically inspect the 

condition of the charger. Contact manufacturer to replace 

any components that have become worn or broken.

Battery replacement/disposal

Battery replacement

The battery should last the service life of the unit. Contact 

manufacturer for any information you may need.

Safe battery disposal

This unit contains a nickel metal hydride or Lithium-Ion 

rechargeable battery pack, which must be must be disposed 

of properly when it will no longer retain a charge.
•   Do not dispose of the battery in fire as this may result in 

an explosion.

•   Before disposing of the battery, protect exposed terminals 

with heavy-duty electrical tape to prevent shorting 

(shorting can result in injury or fire).

•   Do not expose battery to fire or intense heat as it may 

explode.

Summary of Contents for 10307













Reviews: