PROBLEM
The robot
moves
in
one direction.
I
The
robot does
not
move
and
the filtration pump
does not work either. The robot doesn't work any
longer.
I
The pump runs but the robot does not
move. Th
e
robot turns on but stays
in one
spot.
Robot does not climb walls.
The robot goes round in circles.
I
Page 1
3
CAUSE(S)
-An object blocks the rollers, the wheels of the robot
or interfering with the movement of the robot.
- The robot is not connected to a
power source.
- Power
is
off.
- No/not enough power is transmitted to the robot.
- An object bloc
k
s the rollers, the belts, the wheels
of therobot or the path.
- Possibility of motor problem.
-The robot is too heavy.
-The flow is not enough.
-The walls are too slippery.
-The handle of the robot is
correct
ly directed.
-pH level is too high. Keep the pH level close to
7.2 to avoid slippery walls
-A belt is damaged.
-
O
ne of the 4 side wheels is damaged or
unscrewed.
SOLUTION(S)
-
impeller located above the motor.
-
Check that there
is
no foreign object blocking the
hydraulic circuit or the brushes an
d
belts under
therobot and sides.
- Check that the power source is active
by
plugging
another device into the power outlet.
- Check that the power supply is turned on.
- Check all connections of the robot to the power
source.
- Unplug the power and
take out the robot in the
water. Open the cover of the basket and remove the
basket.
- Check that there are no foreign objects in the
impeller located above the motor.
- Check that there
is
no foreign object blocking the
hydraulic circuit or the brushes an
d
belts under the
robot and sides.
- Contact the After-sales Service
- Check that the collection of debris basket isn't full
- Check and clean if need
ed
the impeller of the pump
or the gri
ll
at the top of the impeller (propeller ontop
of the robot toward the handle)
- Presence of algae or fatty deposits
on the walls
.
Remove algae using the chemical treatment of water
and manual
ly
b
rush to remove these fatty deposits.
- Check that the handle of the robot is directed to the
rear. The cable should be above the handle.
- Check the condition of the drive belts.
If necessary, replace
any
faul
t
y belt.
- Check the wheels bolted to the ends of the rollers.
These wheels fit on
to
the ro
ller
and then screw
ed
on
.
(See Chapter 4)
PROBLEM
The robot stops after a few minutes.
The robot moves slower than before.
No
LED
lit on the transformer.
The blue LED on the "No-Twist" floating device
does not light up ( light C of Chapter 9).
The blue light on the transformer is on
but the red
or orange do
not li
ght
up
(timer light B of Chapter 9).
The blue light on the No-Twist Floating device is on
but the cleaner does not work ( light C of Chapter 9 ).
The robot leaves traces on the floor or on the walls.
CAUSE(S)
- Connection of the floating cable.
Check that there are no foreign objects in the
-
Possibility of fault of the floating cable.
- Possibility of motor leakage.
- The robot is too hea
vy
.
- The
water
flow is not sufficient.
- Cables connections
loose/disconnected
.
- The current is not reaching the transformer.
- Bad connection between the transformer and
the No-Twist floating device.
- Possibility of No-Twist floating device problem
- You did not press the on/off button located
above the transformer.
- Cleaner not activated
- Bad cable connections.
-
Possibility of
ransformer problems
- Bad connection between the No-Twist floating
device and the cleaner
- Possibility of No-Twist floating device problem
- Possibility of motor problem.
- State of the brushes and/or transmission belts.
SOLUTION(S)
- Check the connection
s
of the floating cable.
Disconnect and reconnect as neede
d
.
- Check the status of the connectors at the ends of
your cables (damaged, rusted, etc.)
- Check that the dirt collecting basket is not
full.
- Check and clean if necessary the pump impeller or
the gri
ll
above the impeller (propeller at the top of
t
h
e robot towards the handle
)
.
-Check all the cable connections (see chapter 5).
-Check your electrical outlet.
-Check the
cable
connections.
-
C
ontact our Customer Service.
-Turn ON the cleaner by pressing the ON/ OFF
button located on
top of the transformer.
-Check all the connections of the cables between
the transformer and the No-Twist floating device.
-Contact the After-sales Service
-Turn ON the cleaner by pressing the ON/ OFF
button located on top of the transformer.
-Check your electrical outlet.
-Do not use extension cord
-Contact our Customer Service.
-Check if the connection at the
"No-twist" float
outlet, blue outlet "Pool Cleaner"
,
is correct and
waterproof.
-If the blue light C is on, you should also have a red
light on
at the float outlet (light E in Chapter 8).
If
this is not the case, it is likely that the float is
defective.
-If both blue and red lights are on
but the robot does
not work, please contact your dealer or our after-
sales service at service@8streme.
com
-These brushes and belts are wear-and-tear parts
.
Please check them and change them if necessary.
Please contact www.8streme.
com
if you have any other questions.
Page 1
4
