background image

 

2

 

 

 

 

Step 3   Adhere Velcro strips to the bottom of the 5BARz Road Warrior unit and affix the 
counterpart Velcro adhesive strip to the dashboard. Connect the Velcro on the unit to the 

Velcro on the dashboard so the unit is secure.* See Important notes

 

 

Step 4   Plug the connected phone cradle/cigarette adapter into the cigarette lighter 
pushing down to make sure it connects. The arm of the adapter is bendable to fit your 
vehicle’s area. Place your turned-on phone in the cradle and adjust the side clasps to fit 
snuggly by depressing the clasp release on the side of the cradle and adjusting the clasps in 
and out as needed.  

 
Step 5   Find the on/off switch on the side of the phone cradle and turn the unit on and 
start the car. The blue LED light on the front of the 5BARz should be on within 10 seconds.  

 

 

Observe the bars on your phone as you turn the 5BARz

TM 

on -- With the phone in the 

holder, you should see an increase in bars in approximately 10 seconds.  Now you have more 
BARz for better reception and are ready to use your phone and your Bluetooth

® 

device, headset or 

speakerphone. 
 

Note:  The 12-Volt source that is providing power may not power off when you turn your car off.  If the power to the 

5BARz is on when the vehicle is turned off, unplug or switch off the 5BARz when leaving the vehicle – continuous 
operation without the engine running will drain the battery after some period of time (typically one day or more.)

 

 

Note: If multiple cigarette lighter sockets are available, try each to determine which location offers the best 

performance as measured by BARz on the phone.   

 
Important notes: 
 
Note: 
The cigarette lighter power supply and phone cradle must be installed at least 20 cm (or 

approximately 8-inches) away from all persons during normal operation to comply with the FCC’s 
radiofrequency radiation exposure requirement.

 

 
Note:
 Do not place over an airbag. Please check with your state’s regulatory requirements for 
placement of a device on the dashboard. 
 

Note: It is the responsibility of the user to ensure that the 5BARz Road Warrior unit is safely 
secured to the dashboard.  Mount the 5BARz on an area of the dashboard where passengers 
cannot be injured if the 5BARz

 

separates from the dashboard. 

 

III. 

Quick steps to use indoors

  

 

The 5BARz Road Warrior was originally designed for in-vehicle use, however our customers found 
it also works great indoors.  If you want to use the 5BARz Road Warrior indoors at your home, 
office or hotel room, please remember it was not designed to cover the whole room.  The Road 
Warrior works best indoors when resting in the cradle – a blue-tooth enabled headset will give 

you increased mobility within 10-15 feet of the 5BARz unit. 

Summary of Contents for MD015A-800








Reviews: