background image

 

3

 

 

Step 1

   

Place the 5BARz Road Warrior in the area where you want more BARz -- usually 

the closer to a window the better the performance. 

 

  

Step 2   Insert the cable attached to the phone cradle into the port labeled “VDC” 
located on the back of the 5BARz.  
Place the phone cradle as far apart from the 5BARz as 
the cable will stretch for optimal performance. 

 

Step 3   Pry open the easel-like stand on the back of the cradle to hold the phone 
cradle in an upright position.  Place your turned-on phone in the cradle and adjust the side 

clasps to fit snuggly by depressing the clasp release on the side of the cradle and adjusting 
the clasps in and out as needed. (There is no need for the cigarette lighter adapter for indoor 
use.)
 

 

Step 4   Insert the cord from the wall mount power supply line into the power port 
on the back of the 5BARz.
  Next, plug the power supply into the wall socket (use an 

extension cord for longer distances).  Once the unit is plugged in you will see the blue LED 
lights in about 10 seconds. 

 

Observe the bars on your phone after you plug in the 5BARz.  W

ith the phone resting 

in the holder, you should see an increase in bars in approximately 10 seconds.  Now you have 
more BARz for better reception and are ready to use your phone and Bluetooth

® 

device, headset 

or speakerphone. 

 
    

Important Notes 
 

Note: The phone holder must be placed at least 20 cm (or approximately 8-inches) away from all 
persons during normal operation to comply with the FCC’s radiofrequency radiation exposure 
requirement. 
 

Note: For optimal performance place 5BARz

 

in the location with the best serving signal as 

indicated on your phone. (See 

www.cellynx.com/support

 for more details) 

 
Note: Unplug the power supply when not using the 5BARz 
 

Note: The cell phone can be removed from the phone cradle when using the 5BARz

TM

.  However, 

a Bluetooth

®

 device paired to the cell phone while it is resting in the phone cradle is 

recommended for best results. 
 

 
Operation Tips 

 

The 5BARz Road Warrior is compatible with every carrier in the US and Canada  except 

“iDEN” phones used by Nextel, Southern LINC, MiKE (Canada); 3G TMobile’s 3G services 
(TMobile’s voice service is compatible) and WiMax. 

Summary of Contents for MD015A-800








Reviews: