3xLogic VSX-PTZ-2MP-EXT20 User Manual Download Page 48 | Manualshive

Page: 48 / 90

3xLogic VSX-PTZ-2MP-EXT20 User Manual Download Page 48

User Manual

| VISIX 5 Inch Speed Dome Camera

CONFIGURING UPNP™ SETTINGS

Universal Plug and Play (UPnP™)   is a networking architecture that   provides compatibility among
networking equipment, software and   other hardware devices. The UPnP   protocol allows devices to
connect seamlessly   and to simplify   the implementation of networks   in the house and corporate
environments.
With the function enabled, you don’t   need to configure the port   mapping for   each port, and the
camera is   connected to the Wide Area Network via the router.

Steps:

1.

Enter the UPnP™ settings interface.

Configuration >Advanced Configuration >

Network > UPnP

2.

Check the checkbox to   enable the UPnP™ function.
You can edit the Friendly Name of the speed dome. This name can be detected   by corresponding
device, such   as a router.

Figure 6-‐22

Configure UPnP Settings

CONFIGURING NAT (NETWORK ADDRESS TRANSLATION) SETTINGS

Steps:

1.

Set the port mapping mode:

To port mapping with the default port numbers:

Choose

To port mapping with the customized port numbers:

Choose

And you can customize the value of the port number by yourself.

2.

Click

to save the settings.

«
...
46
47
48
49
50
...
»

Summary of Contents for VSX-PTZ-2MP-EXT20



























































































Reviews:

No comments