3xLogic VSX-PTZ-2MP-EXT20 User Manual Download Page 19

Page: 19 / 90

User Manual

| VISIX PTZ Network Camera

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

Descriptions of the live view page:

Figure 4-‐2

Live View Page

Menu Bar:

Click each tab to enter Live View, Playback, Log and Configuration page respectively.

Live View Window:

Display the live video.

Toolbar:

Operations on the live view page, e.g., live view, capture, record, audio on/off, two-‐way audio, etc.

PTZ Control:

Panning, tilting, focusing and zooming actions of the speed dome. The lighter, wiper, one-‐touch focus
and lens initialization control.

Preset/patrol/pattern:

Set and call the preset/patrol/pattern for the speed dome.

Live View Parameters:

Configure the image size and stream type of the live video.

4.3

Starting Live View

In the live view window as shown in Figure 4-‐3, click

on the toolbar to start the live view of the

speed dome.

Figure 4-‐3

Start Live View

Menu Bar

Live view window

Toolbar

PTZ control

Preset/patrol/pattern

Live View Parameters

Click to show or hide
PTZ control panel

Summary of Contents for VSX-PTZ-2MP-EXT20



























































































Search results

Summary of Contents for VSX-PTZ-2MP-EXT20

Reviews:

3xLogic VSX-PTZ-2MP-EXT20, User Manual, Page: 19 / 90

Search results

Summary of Contents for VSX-PTZ-2MP-EXT20

Reviews: