background image

Hardware Install Manual |

 

VISIX 360 Network Camera

 

 

 

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

 

Regulatory Information 

FCC Information 

FCC compliance: 

This equipment has been tested and found to comply with the limits for a digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference when the equipment is operated in a commercial environment. This equipment generates, uses, 

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, 

may cause harmful interference to radio communications. Operation of this equipment in a residential area is 

likely to cause harmful interference in which case the user will be required to correct the interference at his own 

expense.

 

 

FCC Conditions 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

1. This device may not cause harmful interference.

 

2. This device must accept any interference received, including interference that may cause undesired operation. 

EU Conformity Statement 

This product and - if applicable - the supplied accessories too are marked with "CE" and 

comply therefore with the applicable harmonized European standards listed under the Low 

Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS Directive 

2011/65/EU. 

 

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as 

unsorted municipal waste in the European Union. For proper recycling, return this product to 

your local supplier upon the purchase of equivalent new equipment, or dispose of it at 

designated collection points. For more information see: www.recyclethis.info. 

 

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as 

unsorted municipal waste in the European Union. See the product documentation for 

specific battery information. The battery is marked with this symbol, which may include 

lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return 

the battery to your supplier or to a designated collection point. For more information see: 

www.recyclethis.info. 

 

Summary of Contents for VISIX360

















Reviews: