background image

16

Press and hold  

Stop-button for 5 sec.

Press Up-button

*

,

Move roller shutter to desired position

1 x Press  

Up-button 

 PROGRAMMING END POSITIONS

Attention! 

If the upper end point is set, do not move the motor 

upwards! The motor will not stop at the upper end point until the 
lower end point has also been set.

1. Initialization of the  
end point setting:

Beep from motor 

+ down and up

1 x Press button 

P2 / Set Up

1 x Press button 

P2 / Set Up

+

Beep from motor 

+ down and up

+

+

The motor confirms 

the programming

with 3 beeps and 

down and up

OK

2. Setting upper end point:

1 x Press Stop-button 

to stop motor 

+

The motor confirms 

the programming

with 3 beeps and 

down and up

OK

3. Setting lower end point:

Press and hold  

Stop-button for 5 sec.

Press Down-button

*

,

Move roller shutter to desired position

1 x Press Stop-button 

to stop motor

+

The motor confirms 

the programming

with 3 beeps and 

down and up

OK

When setting the upper and lower end points, the motor can be switched to jog mode 
during travel. To do this, press the P2 button during upward or downward travel. The motor 
then moves up or down in small steps, which facilitates the precise setting of the end 
points. 

Activate jog mode: 

During ascent or descent 

1 x Press 

 button P2 / Set Up

3T-MOTORS Radio tubular motors

  |  Programming end positions

Summary of Contents for 3T-MOTORS 3T45-RB

























Reviews: