3onedata IES716-2GS User Manual Download Page 8

Page: 8 / 54

User manual

Page 8

10Base-T /100Base-TX Ethernet port

10Base-T/100Base-TX Ethernet port is located on front panel and the type is RJ45. The pinout of

RJ45 port connects to UTP or STP. The distance is not more than 100m. 100Mbps Ethernet connector

takes 12

0Ωof UTP 5, 10Mbps Ethernet connector takes 1

0Ωof UTP 3, 4, 5.

RJ45 port supports automatically MDI/MDI-X connection. It can connect PC, Server, Converter and

HUB .Corresponding connection of Pin 1,2,3,6 is like this: 1→3, 2→6, 3→1, 6→2. The definition of Pin

is displayed as below.

Information necessary to explain:

Note: “TX±”Transmitting data±, “RX±”receiving data±, “—”no use

MDI

（

straight-through cable

）：

MDI-X

（

Cross over cable

）：

1000SFP fiber port(mini-GBIC)

1000BaseSFP fiber port adopts gigabit mini-GBIC transmission, can choice different SFP module

according to different transfer distance. Fiber interface must use for pair, TX port is transmit side, must

connect to RX (receive side). The fiber interface support loss line indicator.

Suppose

: If you make your own cable, we suggest labeling the two sides of the same line with the

same letter (A-to-A and B-to-B, shown as below, or A1-to-A2 and B1-to-B2).

MDI

MDI-X

TX+

RX+

TX-

RX-

RX+

TX+

RX-

TX-

4, 5, 7, 8

—

Summary of Contents for IES716-2GS























































Search results

Summary of Contents for IES716-2GS

Reviews:

3onedata IES716-2GS, User Manual, Page: 8 / 54

Search results

Summary of Contents for IES716-2GS

Reviews: