background image

802.11n_HT20

23dBm@MCS0, 20dBm@MCS7

802.11g

23dBm@6Mbps, 20dBm@54Mbps

802.11b

23dBm@1Mbps, 23dBm@11Mbps

LTE Operating
Frequency
Band

TDD-LTE

Band38/39/40/41

FDD-LTE

Band1/3/5/7/8/20

WCDMA

Band1/5/8

TD-SCDMA

B34/39

EVDO/CDMA1X BC0
GSM

Band3/8

LTE Bandwidth
(downward,
upward)

TDD-LTE

Rel 9 Cat4 TDD-LTE 112Mbps/30Mbps

FDD-LTE

Rel 9 Cat4 FDD-LTE 150Mbps/50Mbps

DC-HSPA+

42Mbps/5.76Mbps

HSPA+

21Mbps/5.76Mbps

UMTS

384kbps/384kbps

EVDO RevA

3.1Mbps/1.8Mbps

EVDO Rev0

2.4Mbps/153.6kbps

TD-HSPA

4.2Mbps/2.2Mbps

TD- SCDMA

2.8Mbps/2.2Mbps

CDMA 1x

153.6kbps/153.6kbps

EDGE

236.8kbps/236.8kbps

GPRS

85.6kbps/85.6kbps

LTE Sensitivity

GSM

<-108dBm

WCDMA

<-109dBm

TD-SCDMA

<-108dBm

TDD-LTE

Band38/39/40: <-100dBm @5MHz
BW

Band41: <-98dBm @5MHz BW

FDD-LTE

Band1: <-100dBm @5MHzBW

Band3/8: <-97dBm @5MHzBW

Band5: <-98dBm @5MHzBW

CDMA

<-108dBm

EVDO

<-108dBm

Maximum
Transmission
Power of LTE

LTE-FDD/TDD

23 ±2dBm

WCDMA

24 +1/-3dBm

TD-SCDMA

24 +1/-3dBm

EVDO/CDMA
1X

24 ±1dBm

GSM850/900

33±2dBm

GSM1800/1900

30±2dBm

Power Supply

Input

power

supply

Dual power supply redundancy,
voltage range: 12

48VDC,

support non-polarity, reverse
polarity protection, built-in
overcurrent 2.0 protection

48VDC POE power supply

Terminal block

6-pin

5.08mm

pitch

terminal

blocks(power supply occupies 4 pins)

Power
Consumption

No-load

3.38W@24VDC

Full-load

7.15W@24VDC

Operating
Environment

Operating
temperature

-40

75

Storage
temperature

-40

75

Relative
humidity

5%

95%(no condensation)

Protection
grade

IP30(metal)

Summary of Contents for IRT5300-AW-5T2D

Page 1: ...TE antenna interfaces 5 100M copper ports 2 RS 232 485 serial ports Panel Design Top view bottom view and rear view Front view and side view 1 DIN Rail mount 2 SIM slot 3 Grounding screw 4 Terminal block of power supply input 5 DIP switch 6 Console port 7 USB interface 8 WIFI antenna interface 9 WLAN indicator 10 LTE signal strength indicator 11 PoE indicator 12 100M PoE copper port 13 100M copper...

Page 2: ...eration order above DIP Switch Setting This device provides 4 bit DIP switch for function setting where ON is enable valid terminal The definitions of DIP switch are as follows 1 Restore factory setting 2 Reboot 3 Reserved 4 Reserved Console Port Connection This device provides 1 program debugging port based on RS232 serial port which can conduct device CLI command line management by connecting to...

Page 3: ...ted to external device Blinking The input end of DI is communicating with external device OFF The input end of DI hasn t connected to external device Specification Standard Standard IEEE802 3 IEEE802 3u IEEE802 11b g n IEEE802 11i IEEE802 11r IEEE802 3af at Protocol IP Ping Traceroute DHCP Server Relay Client DNS Relay Dynamic DNS Telnet SSH HTTP HTTPS TFTP FTP VLAN IP route static route RIP OSPF ...

Page 4: ...y GSM 108dBm WCDMA 109dBm TD SCDMA 108dBm TDD LTE Band38 39 40 100dBm 5MHz BW Band41 98dBm 5MHz BW FDD LTE Band1 100dBm 5MHzBW Band3 8 97dBm 5MHzBW Band5 98dBm 5MHzBW CDMA 108dBm EVDO 108dBm Maximum Transmission Power of LTE LTE FDD TDD 23 2dBm WCDMA 24 1 3dBm TD SCDMA 24 1 3dBm EVDO CDMA 1X 24 1dBm GSM850 900 33 2dBm GSM1800 1900 30 2dBm Power Supply Input power supply Dual power supply redundanc...

Reviews: