3M Static Monitor 790 User Manual Download Page 8 | Manualshive

Page: 8 / 19

background image

8

3.0 Attaching the 3M

™

Static Monitor 790 to a Workbench or

Equipment Chassis

Refer to Figures 4, 5, and 6

Locate the Mounting Plate.
• Attach the Mounting Plate in the desired location using one of the following

methods:
a. Foam tape (already applied to the Mounting Plate). Clean the surface to be

mounted to with isopropyl alcohol. Remove release liner from tape before
mounting.

b. Two #8 pan head machine or wood screws (not supplied).

• Attach the Static Monitor 790 to the mounted plate as shown in Figure 4.

Align the plate with the opening on the bottom of the monitor and slide
forward onto plate until it latches.

Figure 4: Attachment of Mounting

Plate to 3M

™

Static Monitor 790

Figure 6: 3M

™

Static Monitor 790

attached to equipment chassis

Figure 5: 3M

™

Static Monitor 790

attached to workbench

«
...
6
7
8
9
10
...
»

Summary of Contents for Static Monitor 790




















Reviews:

No comments

Related manuals for Static Monitor 790

Brand: Icare Pages: 3

Brand: VELOCICALC Pages: 6

Brand: Panametrics Pages: 68

Brand: jablotron Pages: 2

Brand: Landis+Gyr Pages: 26

Brand: Landis+Gyr Pages: 3

Brand: Oceanic Pages: 68

Brand: Oceanic Pages: 24

Brand: Lake Shore Cryotronics Pages: 97

Disklavier Mark III Series

Brand: Yamaha Pages: 39

Brand: QEED Pages: 6

Brand: Ecolab Pages: 95

Frontline 802.11

Brand: Teledyne Lecroy Pages: 223

Brand: SecureAlert, Inc. Pages: 7

Brand: GANN Pages: 89

Arrow Mobile Android

Brand: MADDALENA Pages: 12

Brand: Keysight Technologies Pages: 10

Brand: MFJ Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands