3M QT-III Quick Start Manual Download Page 14

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the 

accuracy or completeness is not guaranteed.  Before using this product, you must evaluate it and determine if it is suitable for your intended 

application.  You assume all risks and liability associated with such use.  Any statements related to the product which are not contained in 

3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed 

upon, in writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability. 

This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase.  

3M MAKES NO 

OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR 

A PARTICULAR PURPOSE.

  If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s 

option, to replace or repair the 3M product or refund the purchase price of the 3M product.  

Except where prohibited by law, 3M will not 

be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal 

theory asserted. 

Electrical Markets Division

6801 River Place Blvd. 

Austin, TX 78726-9000 

800-245-3573

Fax 800-245-0329

www.3M.com/electrical

Please recycle

Litho in USA

© 3M 2006 78-8126-9537-3-B

3M is a trademark of 3M Company.
Scotch is a registered trademark of 3M Company.

Notes:

Summary of Contents for QT-III















Reviews: