background image

3M™ 

Digital

 Projector X68 Product Safety Guid

e                                       © 3M 2005

8

6

ENGLISH

Important Note

  1.    Always open the lens shutter or remove lens cap when the projection lamp is on.

  2.   To avoid premature lamp failure, do not change the mounting position of the 

projector (desktop ceiling mount or ceiling desktop mount) and continue to use the 

same lamp.

  3.   To avoid reduced lamp life, do not touch projection lamp with bare fingers.

  4.   To avoid reduced image quality, do not touch projection lens or other internal 

optical components.

  5.   Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other 

than those referred to in the “Operators Guide”.

  6.   For maximum lamp life, do not strike or drop, improperly handle, or scratch the 

lamp glass. Also, do not install an old or used lamp. 

  7.   Keep air filter clean. Refer to the cleaning instructions contained in the “Operator’s 

Guide”.

  8.   Keep all ventilation openings free of any obstructions.

  9.   In some countries, the line voltage is NOT stable. This projector is designed to 

operate safely within a bandwidth of 90 to 132 volts / 198 to 264 volts (50 to 60 Hz) 

±10 volts, but could fail if power drops or surges of ±10 volts occur. In these high-

risk areas, it is recommended to install a power stabilizer unit.

10.    Do not block intake or exhaust air vents. This will cause the projector to over heat 

and shut down.

11.  Do not place the projector in direct sunlight or near a hot object such as a heater.

12.   To prevent damaging the projector, always hold the projector whenever using the 

elevator buttons to adjust the elevator feet.

13.   Use the accessory cable or a designated-type cable for the connection. Some 

cables have to be used with core set. A too long cable may cause certain picture 

degradation. Please consult with your dealer for details. For cables that have a 

core only at one end, connect the core to the projector.

14.   Make sure that you connect devices to the correct port. Incorrect connection may 

result in malfunction and/or damage to the device and/or projector.

15.   Do not place the projector in the side/front/rear-up position, except care of the air 

filter.

Summary of Contents for Multimedia Projector X68













Reviews: