manualshive.com logo in svg

3M GMI PS200-LMP, Operation & Maintenance Manual, Page: 32 / 46

Share
Download
3M GMI PS200-LMP Operation & Maintenance Manual Download Page 32

64220, Rev. 1/April 2019

3M™ GMI™ PS200-LMP AUTO BUMP/CALIBRATION STATION

CREATE/VIEW CERTIFICATES

6-6

6.4. Access Previously Created Certificates

All previously generated certificates are stored in the Generated Certificates folder, as highlighted in 

Figure 6-9:

 

Generated Certificates Folder

.

Figure 6-9: Generated Certificates Folder

This folder contains html files of all previously generated certificates as illustrated in 

Figure 6-10:

 

Gen-

erated Certificates Files

. 

Figure 6-10: Generated Certificates Files

Each html file can be opened to view or print.

6.5. Adding a Company Logo to Certificates

To include a company logo on certificates:
1. Insert the logo file (named logo.jpg) into the Generated Certificates folder on the USB memory 

stick.

2. The logo will be included in the top right hand corner of the certificate.

NOTE: logo.jpg file size must not exceed 200 (W) x 50 (H) pixels.

Summary of Contents for GMI PS200-LMP















































Reviews:

No comments