FORM NO: 5908277 REV: A
6
SAFETY INFORMATION
Please read, understand, and follow all safety information contained in these instructions prior to the use of this Confined Space
Entry/Rescue Device. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.
These instructions must be provided to the user of this equipment. Retain these instructions for future reference.
Intended Use:
This Confined Space Entry/Rescue Device is intended for use as part of a complete personal fall protection or rescue system.
Use in any other application including, but not limited to, non-approved material handling applications, recreational or sports related activities, or
other activities not described in the User Instructions or Installation Instructions is not approved by 3M and could result in serious injury or death.
This device is only to be used by trained users in workplace applications.
!
WARNING
This Confined Space Entry/Rescue Device is part of a personal fall protection or rescue system. It is expected that all users be fully trained in the
safe installation and operation of the complete system.
Misuse of this device could result in serious injury or death.
For proper selection,
operation, installation, maintenance, and service, refer to all Product Instructions and all manufacturer recommendations, see your supervisor, or
contact 3M Technical Service.
•
To reduce the risks associated with working with a Confined Space Entry/Rescue Device which, if not avoided, could result in
serious injury or death:
-
Inspect the device before each use, at least annually, and after any fall event. Inspect in accordance with the User Instructions.
-
If inspection reveals an unsafe or defective condition, remove the device from service and repair or replace according to the User
Instructions.
-
Any device that has been subject to fall arrest or impact force must be immediately removed from service. Refer to the User Instructions
or contact 3M Fall Protection.
-
The device must only be installed in the manner detailed in the Installation Instructions or User Instructions. Installations and use outside
the scope of the instruction must be approved in writing by 3M Fall Protection.
-
The substrate or structure to which the device is attached must be able to sustain the static loads specified for the device in the
orientations permitted in the User Instructions or Installation Instructions.
-
Do not exceed the number of allowable users.
-
Never work below a suspended load or worker.
-
Use caution when installing, using, and moving the device as moving parts may create potential pinch points. Refer to the User
Instructions.
-
Ensure proper lockout/tagout procedures have been followed as applicable.
-
Never attach to a system until it is positioned, fully assembled, adjusted, and installed. Do not adjust the system while a user is attached.
-
Only connect fall protection subsystems to the designated anchorage connection point on the device.
-
Prior to drilling or fastening, ensure no electric lines, gas lines, or other critical embedded systems will be contacted by the drill or the
device.
-
Ensure that fall protection systems/subsystems assembled from components made by different manufacturers are compatible and meet
the requirements of applicable standards, including the ANSI Z359 or other applicable fall protection codes, standards, or requirements.
Always consult a Competent or Qualified Person before using these systems.
-
(TRIPODS) Ensure the lifeline does not extend outside the legs of the tripod.
-
(TRIPODS) Never use the tripod without the leg chains secured in place, or as directed in the User Instructions provided with the tripod.
•
To reduce the risks associated with working at height which, if not avoided, could result in serious injury or death:
-
Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at height. Consult with
your doctor if you have any questions regarding your ability to use this equipment.
-
Never exceed allowable capacity of your fall protection equipment.
-
Never exceed maximum free fall distance of your fall protection equipment.
-
Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns about the use or
suitability of the equipment for your application. Contact 3M Technical Services with any questions.
-
Some subsystem and component combinations may interfere with the operation of this equipment. Only use compatible connections.
Consult 3M prior to using this equipment in combination with components or subsystems other than those described in the User
Instructions.
-
Use extra precautions when working around moving machinery (e.g. top drive of oil rigs) electrical hazards, extreme temperatures,
chemical hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall onto you or the fall protection
equipment.
-
Use Arc Flash or Hot Works devices when working in high heat environments.
-
Avoid surfaces and objects that can damage the user or equipment.
-
Ensure there is adequate fall clearance when working at height.
-
Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the equipment.
-
Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs.
-
If a fall incident occurs, immediately seek medical attention for the worker who has fallen.
-
Do not use a body belt for fall arrest applications. Use only a Full Body Harness.
-
Minimize swing falls by working as directly below the anchorage point as possible.
-
If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the trainee to an
unintended fall hazard.
-
Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.
EN
