background image

 

1

8 of 

1

 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

3M

, Scotchlok and

 Super 33+ are trademarks of 3M Company. 

Scotch is a registered trademark of 3M Company. 
 

Important Notice: 

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy 
or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You 
assume all risks and liability associated with such use. Any statements related to the product, which are not contained in 3M’s current publications, or 
any contrary statements contained on your purchase order, shall have no force or effect unless expressly agreed upon, in writing, by an authorized 
officer of 3M. 

 

Warranty; Limited Remedy; Limited Liability:

 

This product will be free from defects in material and manufacture at the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT 
LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  If this product is defective within the 
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M 
product.  Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M 
product, regardless of the legal theory asserted. 

 

3

 

 
Electrical Markets Division 
6801 River Place Blvd.  
Austin, TX 78726-9000 

 

 

800-245-3573 

Please Recycle.  Printed in USA. 

Fax 800-245-0329 

© 3M 2011 All Rights Reserved. 

www.3M.com/electrical  

78-8

141-4631

-

8

 A 

 

Summary of Contents for Cold Shrink QS-III Splicing Kit



















Reviews: