background image

FORWARD

Contact Information

Read all instructions and warnings before using. Keep these 

User Instructions

 for reference. If you have questions regarding these products contact 3M 

Technical Service.
In United States:

In Canada:

Website: www.3m.com/workersafety

Website: www.3m.com/CA/PPESafety

Technical Service: 1-800-243-4630

Technical Service: 1-800-267-4414

System Description

The 3M™ Adflo™ PAPR Battery Smart Charger for Lithium Ion Battery (35-0099-08) and 3M™ Battery Pack Lithium Ion (35-1099-07) are for use with 

3M™ Adflo™ PAPRs. The 35-0099-08 must be used to charge the Battery Pack 35-1099-07. 

LIST OF WARNINGS WITHIN THESE 

USER INSTRUCTIONS

W

 

WARNING

1.  This product is one component of an approved respiratory protection system. Always read and follow all 

User Instructions

 supplied with your 3M™ 

Adflo™ and 3M™ Headgear and other system components in order to ensure correct system operation. 

Failure to do so may result in injury, 

sickness, or death.

2.  The 3M™ Adflo™ PAPR System is not intrinsically safe. Do not use in flammable or explosive atmospheres, 

doing so may result in serious injury 

or death.

3.  Always correctly use and maintain the lithium-ion battery packs. 

Failure to do so may

 cause fire or explosion or could adversely affect respirator 

performance and 

result in injury, sickness, or death.

a.  Do not charge batteries with unapproved chargers, in enclosed cabinets without ventilation, in hazardous locations, or near sources of high heat.
b.  Do not use charge or store batteries outside of the recommended temperature limits.
c.  Charge in an area free of combustible material and readily monitored. 
d.  Charge only with 3M™ Adflo™ PAPR Battery Smart Charger for Lithium Ion Battery 35-0099-08. 
e.  Do not allow water to enter battery case.

4.  Dispose of lithium ion battery packs according to local environmental regulations. Do not crush, disassemble, dispose of in standard waste bins, in 

a fire or send for incineration. Failure to properly dispose of battery packs may lead to environmental contamination, fire or explosion. 

IMPORTANT:

Before use, the wearer must read and understand these 

User Instructions,

 the 

User Instructions

 for the 3M™ Adflo™ PAPR, and the 

User Instructions

 

for the intended headgear. Keep the 

User Instructions

 for reference. For proper use, see supervisor, refer to the product 

User Instructions

 or contact 3M 

Technical Service at 1-800-243-4630. In Canada, call Technical Service at 1-800-267-4414.

Operating Instructions

W

 

WARNING

The 3M™ Adflo™ PAPR System is not intrinsically safe. Do not use in flammable or explosive atmospheres, 

doing so may result in serious injury or 

death.

Always correctly use and maintain the battery packs. 

Failure to do so may

 cause fire or explosion or could adversely affect respirator performance 

and 

result in injury, sickness, or death.

a.  Do not charge batteries with unapproved chargers, in enclosed cabinets without ventilation, in hazardous locations, or near sources of high heat.
b.  Do not use, charge or store batteries outside of the recommended temperature limits.
c.  Charge in an area free of combustible material and readily monitored. 
d.  Charge only with 3M™ Adflo™ PAPR Battery Smart Charger for Lithium Ion Battery 35-0099-08. 
e.  Do not allow water to enter battery case.

Dispose of lithium ion battery packs according to local environmental regulations. Do not crush, disassemble, dispose of in standard waste bins, in a 

fire or send for incineration. Failure to properly dispose of battery packs may lead to environmental contamination, fire or explosion. 

NOTE:

 Batteries should only be charged in temperatures between 32°F to 104°F (0°C to 40°C). IIf the charger’s LED blinks yellow with one or two red 

flashes, the battery pack is either too hot or too cold to charge. Battery will begin to charge once battery is within acceptable charging temperatures.

New battery packs should be charged upon receipt. The chargers are intended for indoor use where they are protected from moisture. The battery pack 

can be charged separately or attached to the 3M™ Adflo™ PAPR Assembly. The battery should charge to 80% capacity in approximately 3 hours and to 

100% capacity in approximately 6.5 hours, depending upon its residual charge. 
1.  Inspect the battery pack initially and prior to each charge cycle. If any cracks or damage to the case is noted, do not charge the battery pack. Replace 

the battery pack and properly dispose of it in accordance with local regulations.

2.  Place charger and battery pack in a cool, well ventilated location free of airborne contaminants.
3.  Connect the charger output into the battery’s charging socket (Fig. 1).
4.  Plug the charger into a suitable source of AC power (110-120V). See Specification – Battery Pack/Charger section for charger’s LED codes. 

NOTE:

 3M recommends disconnecting the battery pack from the charger once the battery is fully charged. A fully charged battery can be left in the 

trickle-charging mode for a short amount of time (3-4 days). Leaving the battery pack connected to the charger for prolonged periods of time may 

damage the battery pack cells. To avoid damage to the battery pack cells, do not leave it connected to the charger for prolonged durations.

The 3M™ Adflo™ PAPR Motor/Blower has a three-bar battery indicator (Fig. 2) that is operational when the unit is turned on. When all three bars are 

illuminated, the battery has 80-100% capacity. Two bars indicate 20-80% capacity. One bar indicates 5-20% capacity. At approximately 15–30 minutes 

of charge remaining (less than 5%), the bottom LED will begin to flash and the audible alarm will sound.

Installation and Removal of the 3M™ Adflo™ PAPR Battery Pack 

To install the battery pack:
1.  Inspect the hinge and latch on the battery pack and ensure they are clean and undamaged.
2.  Hook the left edge of the battery pack into its holder on the bottom of the unit and press the battery pack into the motor/blower until the catch fully 

engages 

with two audible clicks

 (Fig. 3). 

3.  Gently tug on the battery pack to verify it is secured to the 3M™ Adflo™ PAPR.

To remove the battery pack press the battery pack latch on the right of the battery pack. Pull the battery pack down and out.

Battery Pack Storage 

To help maximize battery pack service life:
•  Store the battery pack at -4°F (-20°C) to 115°F (45°C). R.H. < 85%. Storage of the battery pack outside of this range will shorten service life of the 

battery. 

•  The 3M™ Adflo™ PAPR Battery Pack may remain on the charger for 3 to 4 days after completion of charging, but for maximum battery life, 

disconnect the charger after a full charge has been received. 

•  Battery packs for long-term storage should be disconnected from the motor/blower.
•  Battery packs not intended for immediate or regular use should be charged upon receipt and placed on regular recharge schedule (every 3 months of 

non-use). Prolonged storage of battery packs without regular recharge may damage the battery pack cells.

Refer to 3M Technical Data Bulletin #178 for additional information on battery pack maintenance (www.3m.com/workersafety).

SPECIFICATIONS

Technical

Air flow

Greater than 6 CFM (170 lpm)

Weight (approximate)
1.  Assembly (motor/blower; HE filter; belt; battery pack and 

SG-30W breathing tube)

1.  3.6 lbs (1.65 kg)

2.  Battery Pack

2.  1.0 lb. (0.45 kg)

Battery Pack/Charger
1. Chemistry

1.  Lithium Ion (Li)

2.  Run Time

2.  •  10-12 hours*

•  5.5 hours with OV/AG cartridge*

* New battery pack and HE filter, battery life will be reduced if using at altitudes 

greater than 3500 feet.

3.  Charging Temperatures

3.  32°F to 104°F (0°C to 40°C). If the charger’s LED blinks yellow with one or two red 

flashes, the battery pack is either too hot or too cold to charge.

4.  Storage Temperatures

4.  -4°F (-20°C) to 115°F (45°C). R.H. < 85%. Storage of the battery pack outside of 

this range will shorten service life of the battery.

5.  Battery Pack Service Life

5.  Approximately 500 charges.

6.  Charger Codes

6.  Charger Code Table:

Mode

Description

LED Indication

Yellow steady light

Yellow flashing 

Green steady light

Green flashing

LED indication

Red flashing 2 times

Red flashing 3 times

Red flashing 4 times

Red flashing 5 times

Yellow with 1 red flash

Yellow with 2 red flashes

No indication

Rapid charge

Final charge 

No battery connected

See below

Battery is connected to 

charger with wrong polarity
Charger output is shortened. 

Check output cable 

connection
Battery voltage is low. Check 

battery status or voltage
Safety timer has run out. 

Check battery status or 

capacity
Battery temperature is too 

low (<0°C)

Ready/standby 

Battery temperature is too 

high (>45°C)
Battery voltage is too high. 

Check battery voltage

Error

code

Hazardous Location (Intrinsic Safety)

The 3M™ Adflo™ PAPR Assembly is not approved for use in hazardous or 

intrinsically safe locations.

Summary of Contents for Adflo 35-1099-07










Reviews: