background image

3M and ScaleGard are trademarks of 3M Company. 

© 2020 3M Company. All rights reserved. 

Please recycle. Printed in U.S.A. 

34-8726-0696-6

3M Purification Inc.

400 Research Parkway 

Meriden, CT 06450, U.S.A. 

Tel  (866) 990-9785 

 

(203) 237-5541 

Fax   (203) 238-8701 

www.3MFoodservice 

www.3Mpurification.com

Product Use:

Many factors beyond 3M Purification Inc.'s (3M’s) control and uniquely within user’s knowledge and control can affect the use and performance of 

a 3M product in a particular application. User is solely responsible for evaluating the 3M product and determining whether it is fit for a particular 

purpose and suitable for user’s method of application. 

Warranty, Limited Remedy, and Disclaimer: 

3M warrants that this product (excluding filter cartridge or filter membrane) will be free from defects in material and manufacture for the period of 
(1) year from the date of purchase. The filter cartridge or membrane is warranted to be free from defects in material and manufacture for one (1) 
year. No warranty is given as to the service life of any filter cartridge or membrane as it will vary with local water conditions and water consumption. 

3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY 
OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING 
OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.

If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or 
refund of the purchase price.

Limitation of Liability:

Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, 

incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.

Summary of Contents for 5629101





















Reviews: