3M 2178-XLB Instructions Manual Download Page 16

Page: 16 / 16

3M, Scotchlok and Dual Lock are trademarks of 3M Company. Scotch is a registered trademark of 3M Company.

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed

to be reliable, but the accuracy or completeness is not guaranteed.

Before using this product, you must evaluate it and

determine if it is suitable for your intended application.

You assume all risks and liability associated with such use.

Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements

contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized

officer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase.

3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.

If this product is defective within the warranty period stated above, your exclusive

remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.

Except

where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising
from this 3M product, regardless of the legal theory asserted.

Communication Markets Division

6801 River Place Blvd.

Austin, TX 78726-9000

1-800-426-8688

www.3MTelecommunications.com

Please Recycle. Printed in USA.

78-8135-0094-5-K

Summary of Contents for 2178-XLB

















Search results

Summary of Contents for 2178-XLB

Reviews:

Related manuals for 2178-XLB

Brands by name

Popular brands

3M 2178-XLB, Instructions Manual

Search results

Summary of Contents for 2178-XLB

Reviews:

Related manuals for 2178-XLB

Brands by name

Popular brands