6
7
SPECIFICATIONS
Size
.2 x 2.0 x .2 in. (8. x . x . cm)
Weight
. oz. ( g)
Ingress Protection Rating
IP
Sensor
Electrochemical (factory replaceable)
Operating Humidity
– 90% (non-condensing)
Readout
Direct read LCD
Range
0-99 ppm (CO)
0-200 ppm (H
2
S)
Alarm Indicators
Visual: Flashing LCD display and red LED
Audio: 8 dBA @ foot (0. cm) buzzer
Tactile: Internal vibrator
Alarm Readings
Low, High, Low Battery, Over Range , TWA, and STEL alarms
Alarm Settings
See alarm settings in the table below
Reading Resolution
ppm (readings start at ppm)
Test Function
Self-test on circuitry, battery and alarms. Automated sensor test reminder.
Sensor Replacement
Factory replaceable
Intrinsic Safety
CSA (US) - Class I, Div I, Group A, B, C, D, TA
H
2
S - ppm
110XL
110XL-Series Label
Audio Alarm Opening
(Buzzer)
Sensor Inlet
On/Off/Menu Button
110XL-CO
(Carbon Monoxide)
110XL-H
2
S
(Hydrogen Sulfide)
Alligator Pocket/Belt Clip
LCD Display
Visual Alarm LED
Fig.
Power
Permanently mounted, non-rechargeable .6- volt Lithium battery (factory
replaceable)
Battery Life
2 years from activation (maximum 6. alarm hours – minutes/day)
Radio Frequency Protection
<0% deviation of alarm level when subjected to 0MHz, Watt Radio
@ 2 ft (6 cm)
Keypad
One button operation
Operating Temperature
See table below
Sensor Accuracy (after
calibration)
Carbon Monoxide (CO) – Less than ± 2% of the displayed reading or
ppm, whichever is greater
Hydrogen Sulfide (H
2
S) - Less than ±2% of the displayed reading or
2 ppm, whichever is greater
Non-contaminated
environment
An environment containing less than 0. ppm of hydrocarbons, 0. ppm of
CO, 0.2 ppm of H
2
S, 0.2 ppm of Ammonia, 0. ppm of Hydrogen and 0.2
ppm of other gasses not normally found in the air.
Certified calibration gas*
Refers to a calibration gas sold by M or produced by an ISO 900:2000
certified calibration gas manufacturer. The certified accuracy of the
calibration gas components must be listed on the calibration gas container
and traceable to National Institute of Standards and Technology (NIST) or a
national measurement institute standard reference material.
Warranty
2 years for sensor and electronics (see WARRANTY section)
* A gas analysis certificate of the calibration gas is available if requested.
Sensor
Symbol
Gas
Read by
Sensor
Display
Range
Reading
Resolution
Required
Calibration
Gas
Concentration
Factory
Set Low
Alarm
Factory
Set
High
Alarm
Factory
Set
TWA
Alarm
Factory
Set
STEL
Alarm
Operating
Temperature
Range
CO
Carbon
Monoxide
0 - 99
ppm
ppm
ppm
ppm
200
ppm
ppm
200
ppm
- to 22 ˚F
(-20 to 0 ˚C)
H2S
Hydrogen
Sulfide
0 – 200
ppm
ppm
0 ppm
0 ppm ppm 0 ppm ppm
- to 22 ˚F
(-20 to 0 ˚C)
SPECIFICATIONS (cont.)
WARNING
Using a certified gas with a concentration other than the one listed for this instrument and sensor when
conducting a calibration or calibration verification test (Bump test) will produce inaccurate readings. This
means that higher levels of the gas being monitored may be present and could result in overexposure and
cause sickness or death
. For proper use, see supervisor or
User Instructions
, or call M in U.S.A.,
-800-2-60. In Canada, call Technical Service at -800-267-.