6
Questions? Call 888-888-7985
6
ASSEMBLY DRAWING
STEP 2-
Assembly the
handle
bars
into
STEP 1-
Attach the console
masts to the base frame
A
).
Insert
the
left
console
mast
(
without
a
wire
attached
inside
)
into
the
base
frame
.
Attach
the
left
console
mast
with
four
M
8
X
15
mm
bolts
using
Allen
wrench
.
(
Do
not
tighten
the
bolts
)
B
).
Put
the
lower
console
wire
and
grounded
wire
inside
and
through
the
right
console
mast
using
the
wire
attached
inside
the
right
console
mast
,
insert
the
right
console
mast
into
the
base
frame
,
right
secure
the
console
mast
with
four
M
8
X
15
mm
bolts
using
Allen
wrench
.
(
Do
not
tighten
the
bolts
)
STEP 3-
Screw on the
M8x40mm
bolt
on
handle bars &
tighten
it
.
(A) Refer to the attached drawing, first to screw &
tight the bolts #1 on handle bars,
then
,
to
screw
&
tight
the
bolts
#2
STEP
4-
Attach
the
console
to
the
console
masts
A).Secure with 6 pcs of M8X15mm bolt on the
right console mast,using Allen wrench.Do
the same on left console mast
(Do not tighten the bolts)
(
Caution
:
be
carful
when
connect
two
console
wires
.
There
are
pins
inside
connector
,
the
pins
MUST
be
straight
,
otherwise
it
will
cause
problem
.
The
most
problem
is
that
no
power
on
monitor
,
or
show
E
1)
STEP
5-
Assemble
the
protective
cover
A
).
Assembly
the
protective
cover
to
base
frame
,
secure
with
screw
4
X
10
mm
using
Allen
wrench
.
to the main body
ASSEMBLY INSTRUCTIONS
STEP 1
Assemble the Up-Right tubes
onto Base Frame.
STEP 2
Assemble the handle bars into
the console.
STEP 3
Screw the M8x40mm bolts onto
the handle bars and tighten.
STEP 4
6
ASSEMBLY DRAWING
STEP 2-
Assembly the
handle
bars
into
STEP 1-
Attach the console
masts to the base frame
A
).
Insert
the
left
console
mast
(
without
a
wire
attached
inside
)
into
the
base
frame
.
Attach
the
left
console
mast
with
four
M
8
X
15
mm
bolts
using
Allen
wrench
.
(
Do
not
tighten
the
bolts
)
B
).
Put
the
lower
console
wire
and
grounded
wire
inside
and
through
the
right
console
mast
using
the
wire
attached
inside
the
right
console
mast
,
insert
the
right
console
mast
into
the
base
frame
,
right
secure
the
console
mast
with
four
M
8
X
15
mm
bolts
using
Allen
wrench
.
(
Do
not
tighten
the
bolts
)
STEP 3-
Screw on the
M8x40mm
bolt
on
handle bars &
tighten
it
.
(A) Refer to the attached drawing, first to screw &
tight the bolts #1 on handle bars,
then
,
to
screw
&
tight
the
bolts
#2
STEP
4-
Attach
the
console
to
the
console
masts
A).Secure with 6 pcs of M8X15mm bolt on the
right console mast,using Allen wrench.Do
the same on left console mast
(Do not tighten the bolts)
(
Caution
:
be
carful
when
connect
two
console
wires
.
There
are
pins
inside
connector
,
the
pins
MUST
be
straight
,
otherwise
it
will
cause
problem
.
The
most
problem
is
that
no
power
on
monitor
,
or
show
E
1)
STEP
5-
Assemble
the
protective
cover
A
).
Assembly
the
protective
cover
to
base
frame
,
secure
with
screw
4
X
10
mm
using
Allen
wrench
.
to the main body
Assemble the Upper Console
onto the Up-Right tubes.
STEP 5
Assemble the side covers to the
main body.
(A) Assemble the left Up-Right tube onto the left side of the
Base Frame, use four M8X15mm bolts and the Allen wrench,
but do not tighten yet.
(B) There is a preinstalled guide cable inside the right side
Up-Right tube. Attach the lower Console Data Cable & Ground
Cable from the motor cavity area to the guide cable. Once
attached, find the top portion of the guide cable at the top of
the Up-Right tube and pull the guide cable up through the tube
until the attached Console Data Cable & Ground Cable are
exposed. At this point, secure the cable for later use. Note:
make sure that you do not allow the cable set to slip back down
the Up-Right tube. Assemble the right Up-Right tube onto the
right side of the Base Frame. Use four M8X15mm bolts and the
Allen wrench, but do not tighten yet.
(A) Secure the handle bars onto the upper
console. Insert and tighten bolts as shown
in diagram #1 and #2.
(A) Assemble the side covers to base frame using
screw 4X10mm and the Allen wrench.
(A) Plug and connect the Console Cable and Ground Cable from the
right Up-Right tube to the cables from the Upper Console: Do not “force”
connection, make sure the pins line up evenly. Failure to do so may cause
the pins to bend which will prevent the treadmill from working properly. Refer
to attached drawing. Once the cables are attached to each other, place the
entire Upper Console onto the Up-Right tubes. (Make sure not to pinch Data
Cables between Upper Console and Up-Right tubes). Align the bolt holes
from both Up-Right tubes with the bolt holes from the Upper Console and
insert and tighten 6 pieces of M8X15mm bolt as shown. Again, make sure
that cables are not pinched between any parts of the treadmill.
