3Dlabs Wildcat II 5000, User Manual

Page: 18 / 51

Setup
3Dlabs Graphics Accelerator Card User's Guide
22
Installing the Wildcat II 5000 Windows NT or Windows 2000 driver
1. Start up Windows and log onto an account with administrative privileges.
2. Place the 3Dlabs driver CD in the appropriate drive. The 3Dlabs driver installation program menu
will appear.
Note: If the installation program menu does not appear, you can access the installation
program through My Computer. Click the drive where the driver CD is located to run the
installation program. If the installation program still doesn’t run, right click Start and choose
Explore to locate the drive. In the 3Dlabs driver CD root directory, double click
WILDCAT
.
EXE
to launch the installation program.
3. Click Install Driver, then choose your operating system from the list.
4. After the driver files are copied, click Quit to exit the installation program.
5. Remove the driver media from the disk drive and restart the workstation.
6. After the system restarts and you log on, a message displays stating that a new display driver has
been installed, and that you should use the Display option in the Control Panel to select the
preferred display resolution. Click OK.
eÉáÇá=aêáîÉêë=Ñçê=^ìíçaÉëâ=^ééäáÅ~íáçåë
eÉáÇá=aêáîÉêë=Ñçê=^ìíçaÉëâ=^ééäáÅ~íáçåë eÉáÇá=aêáîÉêë=Ñçê=^ìíçaÉëâ=^ééäáÅ~íáçåë
eÉáÇá=aêáîÉêë=Ñçê=^ìíçaÉëâ=^ééäáÅ~íáçåë====
The Wildcat II 5000 Heidi
®
device driver allows full screen multisampling of and compatibility with
AutoDesk applications as well as hardware acceleration of the Wildcat II 5000 through the use of
OpenGL. To install the Heidi driver and to activate full screen multisampling, click either the Nt4 or W2k
folder (which ever is appropriate for your system) in the 3Dlabs driver CD. Then, open the Heidi
directory and double click
SETUP
.
EXE
to launch the setup program.
PÇëã~ñ=aêáîÉê PÇëã~ñ=aêáîÉê PÇëã~ñ=aêáîÉê PÇëã~ñ=aêáîÉê====
To install the 3dsmax
®
driver, click either the Nt4 or W2k folder (which ever is appropriate for your
system) in the 3Dlabs driver CD. Then, open the 3dsmax directory and double click
SETUP
.
EXE
to launch
the setup program.
sÉêáÑó=íÜÉ=aÉÑ~ìäí=sáÇÉç=aáëéä~ó=aêá sÉêáÑó=íÜÉ=aÉÑ~ìäí=sáÇÉç=aáëéä~ó=aêá sÉêáÑó=íÜÉ=aÉÑ~ìäí=sáÇÉç=aáëéä~ó=aêá sÉêáÑó=íÜÉ=aÉÑ~ìäí=sáÇÉç=aáëéä~ó=aêáîÉê= îÉê= îÉê= îÉê=====
This section describes how to verify the correct display driver is loaded on your workstation.
Verifying the default video display driver in Windows NT
1. From the operating system Start menu, go to Settings/Control Panel/Display, and click the
Settings tab on the Display Properties dialog box.
2. Click Display Type, then verify that Wildcat II 5000 is listed under Display. This indicates
that the appropriate driver is installed.
3. Click Cancel to close the Display Properties dialog box.