background image

 

 

 

3Dlabs Oxygen GVX210 User's Guide   

 

 

ii 

Copyright 2000 by 3Dlabs, Inc. 

3Dlabs, GLINT and Permedia are registered trademarks, and Oxygen and PowerThreads are trademarks of 
3Dlabs, Inc. or 3Dlabs Inc. Ltd. Pentium is a registered trademark of Intel. OpenGL is a registered trademark 
of Silicon Graphics, Inc. Soft Engine is a trademark of Vibrant Graphics, Inc. AutoCAD is a registered 
trademark of AutoDesk Inc. Colorific is a registered trademark of E-Color, Inc. Microsoft and Windows NT 
are registered trademarks of the Microsoft Corporation. Athlon and 3DNow! are registered trademarks of 
AMD. All other trademarks and registered trademarks are the property of their respective holders. 

Caution: Changes or modifications to the Oxygen GVX210 graphics accelerator card not expressly approved 
by 3Dlabs, Inc. voids the user’s warranty. 

FCC Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 
frequency energy. If product is not installed and used in accordance with the instruction manual, it may cause 
harmful interference to radio communications; however, there is no guarantee that interference will not occur 
in a particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:  

1.  Re-orient or relocate the receiving antenna. 
2.  Increase the separation between the equipment and receiver. 
3.  Connect the equipment to an outlet on a circuit different from that to which the receiver is 

connected. 

4.  Consult 3Dlabs or an experienced radio/TV technician for assistance.  

Compliance with FCC Rules requires that a shielded cable be used to connect to other equipment. This 
device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this 
device may not cause harmful interference, and 2) this device must accept any interference received, including 
interference that may cause undesired operation.  

This Class B digital apparatus meets all the requirements of the Canadian Interference- Causing Equipment 
Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le material 
brouilleur du Canada.  

3Dlabs, Inc. makes no representation that the use of its products in the manner described in this publication 
will not infringe on existing or future patent rights, nor do descriptions contained in this publication imply 
the granting of licenses to make, use, or sell equipment or software in accordance with the description. 

 

Specifications Subject to Change With Notice 

 

P/N 62-000002-001, Rev. A (Final) 

Summary of Contents for Oxygen GVX210


















































Reviews: