manualshive.com logo in svg

3Dlabs Oxygen GVX210, User Manual

Share
Download
3Dlabs Oxygen GVX210 User Manual Download Page 30

Software Configuration 

 

 

 

3Dlabs Oxygen GVX210 User's Guide   

 

 

20 

Configuring your Oxygen GVX210 Card for Stereo Viewing 

The Oxygen GVX210 card supports 3D stereo viewing. This requires that the appropriate equipment such as 
stereo glasses be connected to the 3-pin miniature DIN connector on the Oxygen GVX210 card. It is 
recommended that you use a monitor with a screen refresh frequency of at least 100 Hertz.  

In addition, it is recommended that you turn off fluorescent lighting before viewing stereo images to prevent a 
possible headache. 

To set up and configure stereo viewing 

1.  Connect the stereo hardware to the round, stereo connector on the Oxygen GVX210 card. See the 

documentation that came with your stereo hardware. 

2.  In the Display Properties Control Panel, click the 3Dlabs tab. 
3.  In the 3Dlabs Display Properties screen, click Advanced. 

 
4.  Click the OpenGL Support tab. 

Summary of Contents for Oxygen GVX210


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands