3D Hobby Shop Extra SHP 47" Assembly Manual Download | Manualshive

Page: 10 / 20

background image

10

Apply two large drops of thin CA glue to each elevator hinge. Allow to soak in and cure. Do not use any
accelerator on this glue, allow the glue to fully soak in.

Remove covering over slot in bottom of rudder as shown.

«
...
8
9
10
11
12
...
»

Summary of Contents for Extra SHP 47"





















Reviews:

No comments

Related manuals for Extra SHP 47"

Brand: Aquila Pages: 50

Brand: Gin Gliders Pages: 50

Brand: Independence paragliding Pages: 16

Brand: North Kiteboarding Pages: 30

Brand: Comco Pages: 36

Blanik Electro ARF SKG Series

Brand: Hacker Pages: 16

Brand: Beechcraft Pages: 236

Brand: ICARO paragliders Pages: 22

Brand: LittleCloud Pages: 6

Brand: Naish Pages: 26

Brand: SUP’AIR Pages: 26

McDonnell-Douglas MD-11

Brand: PMDG Pages: 87

Brand: FireBird Pages: 84

Mooney M20E 1971

Brand: Chaparral Pages: 92

Brand: Bruce Goldsmith Design Pages: 34

Brand: Bruce Goldsmith Design Pages: 36

Brand: Bruce Goldsmith Design Pages: 36

Brand: Bruce Goldsmith Design Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands