background image

Copyright © 2004 3Com Corporation.  All rights reserved.  3Com, and the 3Com Logo are registered trademarks 
of 3Com Corporation. All other company and product names may be trademarks of the respective companies with 
which they are associated.
09-2330-000 Rev AA 

Published January 2004

Industry Canada Notice (Applicable to Use Within Canada)

This device complies with Canadian RSS-210.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away 
from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is 
subject to licensing.

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit 
RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from 
Health Canada’s web site www.hc-sc.gc.ca/rpb.

Avis de Conformité à la Réglementation d’Industrie Canada

Pour empêcher toute interférence aux services faisant l'objet d'une licence, cet appareil doit être utilisé à 
l'intérieur seulement et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.

L’installateur du présent matériel radio doit s’assurer que l’antenne est située ou pointée de manière à ce que 
cette dernière n’émette pas de champs radioélectriques supérieurs aux limites specifées par Santé Canada pour 
le grand public; consulter le Code de sécurité 6, disponible sur le site Web de Santé Canada, à l’adresse 
suivante: www.hc-sc.gc.ca/rpb.

Safety Compliance Notice

This device has been tested and certified according to the following safety standards and is intended for use 
only in Information Technology Equipment which has been tested and certified to these or other equivalent 
standards:

•   

UL Standard 60950, 3rd Edition / CSA C22.2 No. 60950-00

•   

IEC 60950

•   

EN 60950

Summary of Contents for WL-463










Reviews: