3Com VCX V7000 Maintenance Manual Download | Manualshive

Page: 167 / 344

background image

Overview of a 7.0 to 7.1 Upgrade

167

Overview of a 7.0
to 7.1 Upgrade

This section provides an overview of the procedures required to upgrade
your VCX system, to an operational state, from version 7.0 to 7.1.

This appendix describes how to upgrade a VCX server by entering
commands at a locally attached console. You can also upgrade a VCX
server remotely by using 3Com Corporation’s Enterprise Management
Suite (EMS). EMS is an SNMP-based client/server application. Refer to the

Enterprise Management Suite User Guide for VCX V7000 Components

for information.

This section assumes the VCX system is successfully operating at version
7.0.7c before you perform the upgrade. If your system is running an
earlier version of VCX 7.0 software (or VCX 6.0 software), you must
upgrade to 7.0.7c before upgrading to version 7.1.

All components in a VCX system

must

run the same version of VCX

software. This requirement has the following implications:

■

You cannot upgrade or downgrade one component in a VCX system
and not upgrade or downgrade the other system components.

■

If you add a server to an existing VCX system (for example, a branch
office), the VCX components on the new server must be installed with
the same version of the VCX software as the existing components.

CAUTION:

3Com Corporation

strongly

recommends that you perform

backups of your VCX system on a regular basis, for example, weekly.
These backups should include provisioning database and voicemail
database content.

■

See

for information on backing up the provisioning data

stored in the VCX Authentication and Directory server database.

■

See the

IP Messaging Module Operations and System Administration

Guide

for information on backing up voicemail and other IP

Messaging data.

In addition,

BEFORE

you upgrade your VCX system to a new release,

perform these backups again. If the upgrade fails and you must
downgrade, you can restore data from these backups as part of the
downgrade procedure.

«
...
165
166
167
168
169
...
»

Summary of Contents for VCX V7000

























































































































































































































































































































































Reviews:

No comments

Related manuals for VCX V7000

Brand: Panasonic Pages: 312

Brand: Olympia Pages: 54

Brand: Hanlong Pages: 57

W56P Telesystem

Brand: Yealink Pages: 12

Verizon One Talk W60B

Brand: Yealink Pages: 8

Brand: Yealink Pages: 2

T46S Skype for Business

Brand: Yealink Pages: 2

Brand: Yealink Pages: 533

One Touch 997D Ultra

Brand: Alcatel Pages: 21

STORM 9500 - STORM 9530 SMARTPHONE

Brand: Blackberry Pages: 36

Brand: Fysic Pages: 8

Brand: Alcatel Pages: 27

Brand: PSC Pages: 32

Brand: Pantech Pages: 97

Brand: Yeastar Technology Pages: 8

Verizon TXT8035PP

Brand: Pantech Pages: 50

Brand: Interlink electronics Pages: 16

Brand: Azumi Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands