background image

 

Part No. 1-024-2301
Published October 1999

 

O

 

FFICE

 

C

 

ONNECT

 

 ISDN LAN M

 

ODEM

 

R

 

ELEASE

 

 N

 

OTE

 

V. 6.2.0 (ST) 

 

AND

 

 5.3.0 (U)

 

Introduction

 

This release note describes the following enhancements made to the 
OfficeConnect ISDN LAN Modem as part of the latest firmware releases.

 

 

Enhanced Dial-in Support 

 

 

Callback Feature

 

 

Upgrade Check Feature

 

 

Local DNS Table

 

 

LAN Modem Desktop Manager (Windows 95/98/NT)

 

 

Miscellaneous Enhancements

 

Enhanced Dial-in 
Support

 

Previously, the LAN Modem provided limited dial-in capability, such as accessing a 
remotely located LAN Modem for remote configuration or to check statistics. Now 
Dial-in support has been enhanced to extend access to workstations or servers 
located behind a remote LAN Modem.

 

Dial-in Applications

 

The following dial-in scenarios are supported by the LAN Modem. If you would 
like more detailed descriptions of these scenarios, refer to “Understanding the 
Three Dial-in Scenarios” later in this release note.

 

Dial-In 
Wizard 
Profile Name Network Scenario

 

Single User

Terminal adapter calls into a LAN Modem.

Public telephone

network

AL

ER

T

LA

N S

TA

TU

S

PO

WE

R

B1

B2

TX

1

2

3

4

CO

LL

IS

DN 
OK

ISD

N L

AN

 M

ode

m

3C

892

Small office LAN

OfficeConnect

ISDN LAN Modem

ISDN BRI line

Terminal adapter

(ISDN modem)

Telecommuter

PWR TEST D B1 B2 SD RD DTR 

3ComImpact IQ

¤

Com

Summary of Contents for OfficeConnect 3C891A

























Reviews: