manualshive.com logo in svg

3Com CT1, Release Note, Page: 5 / 7

Share
Download
3Com CT1 Release Note Download Page 5

 

5

Closed user group (CUG) is a call restriction service among the optional services of 
X.25. It is mainly used to restrict originating or receiving call capabilities for data 
transmission equipment (DTE) users. The users in the same CUG can still call each 
other, but users of different CUGs cannot. As a result, this allows you to form a 
private data communication subnet on an X.25 public data communication network.  
 
The X.25 CUG service can be configured using these CLI commands: 
 

x25 map protocol protocol-address x121-address x.121-address  
closed-user-group group_number 
x25 call-facility closed-user-group group-number undo x25 call-facility closed-

user-group 

x25 cug-service [ incoming-access ] [ outgoing-access ] [ suppress { all | 

preferential } ] 

undo x25 cug-service 
x25 local-cug cug-number network-cug cug-number [ no-incoming ] [ no-

outgoing ] [ preferential ] 

undo x25 local-cug cug-number 
display x25 cug 

 

3.

 

BRI 128K Leased Line 

 

BRI stands for Basic Rate Interface, which is the basic ISDN configuration. This 
configuration consists of two B-channels that can carry voice or date at a rate of 
64Kbps, and one D-channel, which carries call-control information. The current 
release supports a 128Kbps leased line by combining the two 64Kbps B-channels into 
a single 128Kbps physical channel. 
 
You can use these CLI commands to configure the ISDN 128K leased line: 
 

dialer isdn-leased channel-number 
undo dialer isdn-leased channel-number 
dialer isdn-leased 128k 
undo dialer isdn-leased 128k 
isdn link-mode p2p 
undo isdn link-mode p2p 

 

4.

 

HWPing 

 
HWPing is a tool used for testing the performance of the protocols operating on a 
network. It is an enhancement to the ping function that only allows you to test the 
roundtrip delay (time required for a packet to travel from the local end to a specified 
destination and return to the local end again). HWPing enhances the ping function by 
detecting the state (enabled or disabled) of a DLSW, DHCP, FTP, HTTP, or SNMP 
Server, and testing the response time for each type of service. 
 

http://www.3com.com/ 
Part No.

 10014533

 

Published August 2004 

Summary of Contents for CT1








Reviews:

No comments