manualshive.com logo in svg

3Com CT1, Release Note, Page: 2 / 7

Share
Download
3Com CT1 Release Note Download Page 2

 

2

4.

 

The 'info-center logbuffer filter' command supports four new filter parameters, 
L2TP, EC (encryption card), IPSEC, and IKE. 

 

Bugs Fixed in this Release 

 
 

System/Interface: 

 

•

 

Previously, the router would forward packets with a field length set to zero across 
the T1 WAN interface. This would cause the router receiving these packets to 
reboot. In the current release, the router checks the field length of outbound 
packets and drops any with a field length of zero. 

 

•

 

In the past, a user would not be able to access the system file if a remote upgrade 
operation did not complete successfully. For example, if the user did not respond 
to the 'writing to flash' query before the telnet session timed out, no user at any 
location would be able to access the system file. The only way around this was to 
reboot the router.

 

 

•

 

In earlier releases, it is possible for the 301x router to run out of memory. The 
system would fail to login via telnet and the ‘display current’ command would fail 
with insufficient memory error.

 

 

•

 

Previously, if a combination of eight MIM cards were installed in the 5680 device 
simultaneously, the device would be unable to boot up. 

 

•

 

In earlier releases, the system clock would revert back to GMT settings when the 
router underwent a reboot operation. 

 

 
Link Layer/Network Protocol: 

 

•

 

In earlier releases, the router 5680 would corrupt UDP packets from the LAN 
Bridge-set 2 to the WAN bridge-set1. The corrupted packets were layer 3 
broadcast packets, including DHCP requests. 

 

•

 

In previous releases, the router would not place ARP responses in the ARP cache 
when it was configured in bridge mode and IP routing mode. An ARP request 
from the router to the client would be entered in the cache as all zeros. Therefore, 
it was not possible to manage the router until the client pinged the router. In this 
release, the router creates the correct ARP entry in the ARP cache. 

 

•

 

In earlier releases, ISDN would not work with Lucent 5 (AT&T 5ESS), or 
National ISDN. This was because there was no support for North American 
switch types for T1 PRI interfaces. 

 

http://www.3com.com/ 
Part No.

 10014533

 

Published August 2004 

Summary of Contents for CT1








Reviews:

No comments