background image

7

lower measurement range.

Before using the device, check the
housing and the measurement
cables for any damage.

Do not conduct measurements in
a damp environment. Workplace,
hands, shoes and floor must be
dry.

Before opening the housing all
measurement leads are discon-
nected from the device.

2. Description, technical data

Active analog multimeter with a
slide switch for selection of the op-
erating mode and a rotary switch to
select the measurement range as
well as a scale with the mirrored
background for parallax-free read-
ings with a zero-point adjustable to
the center or the left of the scale.
By adjusting the electrical zero-point
to the center of the scale bipolar DC
voltage and current measurements
can be conducted without worrying
about polarity. The device is ex-
tremely robust in terms of load ca-
pacity and is equipped with excel-
lent overload protection due to its
two anti-parallel diodes as well as
moving coil movement which is not
sensitive to external electromagnet-
ic fields. The safety connection sock-
ets offer protection against acciden-
tal touch contact. After approx. 45
mins the battery is automatically
switched off. The power can be re-
established by turning off and on
using the slide switch for the oper-
ating mode. The robust plastic hous-
ing and the spring-connected bear-
ing jewels of the movement guar-
antee protection against damage

caused by mechanical stress.
Measurement ranges:
Voltage measurement:

DC

Meas. range Internal resistance

100 mV

10 M

300 mV

10 M

1 V

10 M

3 V

10 M

10 V

10 M

100 V

10 M

300 V

10 M

AC

Meas. range Internal resistance

3 V

1 M

10 V

1 M

30 V

1 M

100 V

1 M

300 V

1 M

Current measurement AC/DC:

Meas. range

Voltage drop

0.1 mA

55 mV

1 mA

55 mV

10 mA

55 mV

100 mA

55 mV

1 A

53 mV

3 A

51 mV

Accuracy: DC class 2; AC class 3
Effective variables and nominal op-
erating ranges:
Temperature 0 – 40° C: ± 2% / K
Frequency for all measurement
ranges:

±2.5% at 30 Hz up to
1.5 kHz ± 5% at 1.5 kHz
up to 3 kHz

Reference conditions:
Ambient temperature: +23° C ± 2 K
Frequency:  50 to 60 Hz
Waveform:   Sinusoidal

Summary of Contents for U17450






Reviews: