95
2N TELEKOMUNIKACE a.s., www.2n.cz
PRI1 (p1-32)
– define one PRI1 channel or a range of PRI1 channels via
which call routing will be enabled.
PRI2 (exx,E)
– any of the PRI2 channels can be used for call routing.
PRI2 (e1-32)
– define one PRI2 channel or a range of PRI2 channels via
which call routing will be enabled.
VoIP (vxx,V)
– calls are routed via the VoIP interface.
Prefix list
– prefixes to be used for a selected LCR row. Set up to 32 prefix lists.
Prefix list 1–32
– call routing will obey the rules set in Prefix list 1–32.
The count of digits to be dialled is governed by the
setting.
Prefixes
All prefixes
– all the prefix lists are permitted. Prefix lists 1–32 will be
searched from 1 to 32. The first match will be used routing. For incoming
GSM calls, the Count of digits from the
GSM incoming group
parameter will be applied.
Count of digits
– all the prefixes are permitted. Routing is only limited by
the count of digits to be dialled.
Time limitation
– set a time validity limitation for a selected LCR row.
Weekend usage
– enable/disable a row on weekends.
it
Call duration lim
– set the maximum duration (minutes) for an outgoing call
to the GSM/UMTS network.
Groups
– define the outgoing GSM groups or interface via which outgoing calls
will be routed from
. If the defined interface is inactive or the
2N
StarGate
®
outgoing GSM group tariff is exhausted, the next row will be applied.
GSM groups 1–32
– outgoing GSM groups. Set the tariff to be used. Refer
to the GSM outgoing groups subsection for details.
PRI1 (P)
– ISDN PRI1 interface. Refer to the
ISDN parameters
subsection for details.
PRI2 (E)
– ISDN PRI2 interface. Refer to the
ISDN parameters
subsection for details.
VoIP (V)
– VoIP interface. Refer to the
subsection for
VoIP parameters
details.
Tariffs
– select the tariff group (free minute counter) to be used for the outgoing
call. Refer to the GSM outgoing groups subsection for details.
Ignore tone detection in last group
– having detected a user defined tone
(refer to GSM basic settings), the GSM gateway automatically terminates the call
and seeks for another call setup way. If this parameter is activated, the GSM
gateway ignores the tone detection results and sets up a call when this is the
only possible call establishing way.
CLIP Routing Table + CallBack
Use the table to set a fixed CLIP assignment of incoming CLIPs from GSM to the
numbers of extensions to which incoming calls are routed automatically. Also, set the
CLIP list in the GSM network for which CallBack is enabled.
GSM number (CLIP)
– user Id in GSM/UMTS.
Used service
Note
If you use tariff routing, set the tariffs properly in the GSM outgoing
groups subsection
The maximum count of LCR table records is 64.
The rules are applied to calls sequentially, starting from the first rule. If all
the set rules are met in a row, the call is routed according to the row.
Call routing from PRI1/PRI1, PRI2/PRI2 and VoIP/VoIP is not supported.
Such calls will be rejected by
.
2N StarGate
®
Summary of Contents for stargate
