2N Ateus-EasyGate User Manual Download Page 3

Page: 3 / 35

User Manual Versions

Version Amendments to Earlier Versions

1.00

The User Manual applies to EasyGate FW Version 1.00D.

1.01

New parameter for dial tone setting.

LED indications updated.

The User Manual applies to EasyGate FW Version 1.00E

1.02

Default setting for dial tone is continuous tone now.

The User Manual applies to EasyGate FW Version 1.00F

1.03

New function: tariff metering with 16 or 12 kHz pulses.

New function: call connect and disconnect signaling by 16 or 12 kHz pulses.

The User Manual applies to EasyGate FW Version 1.00G

1.04

Continuous dial tone.

Chapter 2.2 modified.

SMS input parameters added.

Upgrade

The manufacturer continuously meets customer requirements by improving the

firmware. For the latest EasyGate processor firmware, programming tool and User
Manual see

www.2n.cz

. For a detailed description of the EasyGate firmware upgrade

refer to the section devoted to the PC programming tool.

Summary of Contents for Ateus-EasyGate




































Search results

Summary of Contents for Ateus-EasyGate

Reviews:

Related manuals for Ateus-EasyGate

Brands by name

Popular brands

2N Ateus-EasyGate, User Manual

Search results

Summary of Contents for Ateus-EasyGate

Reviews:

Related manuals for Ateus-EasyGate

Brands by name

Popular brands