247Security ZEUS Pt User Manual Download

Page: 13 / 71

247Security Inc. | 4400 North Point Parkway, Suite # 158, Alpharetta, GA 30022, USA | 1-866-693-7492 | www.247securityinc.com

USER MANUAL,

ZEUS Pt

1.4.3

AUDIO/VIDEO OUT CONNECTORS

Connector type: RCA Jack

Pin Number

Signal

Description

Pin out

Inside

Audio

Audio Signal

Outside

GND

Ground

Inside

Video

Video Signal

Outside

GND

Ground

1.5

BACK CONNECTORS

1.5.1

POWER INPUT CONNECTOR

The ZEUS PT has a built-in Intelligent power circuit that can operate from +6.5v ~ +16V DC-IN. A

constant 12v, Ignition and Ground are required. The DVR is energized by the vehicle’s ignition signa and

uses this signal to trigger start up, the power shut-down delay and the timing circuitry. The system will

remain ON until the ignition signal has been cancelled and the shut-down delay time has been reached.

The system will then go through its normal shutdown procedures before completely powering down.

Pin Number

Signal

Description

Pin out

ON/OFF

On/Off Switch

On when 6V ~ VIN

Off when 0V ~ 0.5V

GND

Ground

VIN

Input voltage (+8V~+16VDC)

GND

Ground

1.5.2

BATTERY LOOPBACK PLUG, UPS OPERATION

The ZEUSPT has an on-board UPS battery system for providing backup power for up to 15

minutes after main power has been lost. The UPS battery will also keep the DVR running in case of over

voltage (greater then 16VDC) and low voltage (less then 8VDC). This plug is also needed to allow the on-

board battery to charge once power is restored. The DVR systems require a battery loopback Plug to

enable this feature. Installers should connect the battery loopback plug to the DVR only after the device

has been fully installed and connected to the vehicle power source. Remove the loopback plug and store

Summary of Contents for ZEUS Pt







































































Search results

Summary of Contents for ZEUS Pt

Reviews:

Related manuals for ZEUS Pt

Brands by name

Popular brands

247Security ZEUS Pt, User Manual

Search results

Summary of Contents for ZEUS Pt

Reviews:

Related manuals for ZEUS Pt

Brands by name

Popular brands