348. [VLAN_Web] Try to display index 1 (Advanced Application >VLAN > index 1), web
disconnected
349.
[VRRP] VRRP can’t response ping in different routing domain.
350. [Rmirror] When monitor-port in local mirror and connected-port in Rmirror get conflict,
then erase running, the Rmirror still could not work correctly. (In egress direction, the
connected port should be double tagged packets, not original packets).
351. [Rmirror] Configure Rmirror VLAN and Static VLAN, CLI will pop error messages.
ERROR: PORT 1 has been associated with a VLAN! The behavior is abnormal.
352. [Help] the format for Help was incorrect
353. [MIB-zyxelRemotePortMirror] When running SilverCreek scripts twice, then erase
running configuration via CLI, the default configuration will be disappeared.
354. [Rmirror] After removing source reflector port, the setting is correct. Sometimes, the LED
should be light off, not light on.
355.
[Static Arp GUI] The word for the ”Delet” button is misspelling, it should be ”Delete”.
356. [Clustering Management] In the help, the description for Cluster management should be
Cluster management allows you … not managementallows…
357.
[SNMP] In help, Dyinggasp should be in a small letter ”d” not capitalized
358. [Protocol-based VLAN] in help, the path for VID should be Advanced Application not
Advanced Applications in the description column
359. [Bandwidth Control] in Help, there has an x-
tra letter ”T” after the definition of the
bandwidth control
360. [Subnet-based VLAN] in help, the path for VID should be Advanced Application not
Advanced Applications in the description column
361. [Port setup] it should be clear define / label for which models support 10G (Speed/Duplex)
and Media Type column
362. [Rmirror] Enable connect port A and disable connect port A, port A will be Rmirror VLAN
member. It will cause port A could not belong to reflector port.
363. [Rmirror] Enable and disable reflect port in different Rmirror VLAN will cause the
behavior is abnormal
364. [Rmirror] Enable and disable reflect port in different Rmirror VLAN will cause the
behavior is abnormal.
365. [DHCP Relay Option82 Profile] Create maximum circuit-id (64) string and remote-id (64)
string in web page, CLI only display 32 circuit-id string and 32 remote-id string.
366. [Static Route] Create IP address (A) in VLAN interface, then create static route with next
hop = IP address (A), then create IP address (A) in VLAN interface again, CLI will pop
error messages.
367. [Flow Control]After backup and restore configuration file or system reboot, flow control
could not work correctly cross unit.
368. [MLD] In web page, configure query interval, query max response time in downstream,
and query interval, query max response time, robustness variable, last member query
interval in upstream, it will inconsistent between CLI (show ipv6 MLD snooping VLAN) and
Web. But, show running is correct.
369. [10G module] Enable 10G module in DAC10G mode, it could not be flushed successfully
after erase running.
370. [POE] Configure maximum power in PWR, show PWR could not display the maximum
power state without connecting PD.
371. [POE] When user-defined PoE maximum power is less than PD required power, the
alarm LED will light on.
372. [MIB-zyxelIpv6PathMtu] When using MIB Browser to get the zyxelIpv6PathMtu (OID:
1.3.6.1.4.1.890.1.15.3.36) value continuously, sometimes it will pop error message
-
”Error:SNMP Unknown Object Identifier”.
373. [Diagnostic] The cable diagnostic display wrong information while port inactive by
errdisabe/loopguard/intrusion.
374. [DHCP Snooping] the string length for both circuit-id and remote-id in Help and GUI are
inconsistent (GUI, both circuit-id and remote-id can be set up to 64 characters; Help, both
circuit-id and remote-id can be set up to 32 characters)
375. [Static Arp] when static ARP
and VLAN 1’s IP were duplicated which caused erase
running-config command does not work at this time
376. [SNMP Group] Create SNMPv3 user with read/write group. But, the user can access
privilege 14 MIB (ex: reboot, configuration save, AAA)
