ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 206 / 282

Dimension ES-3148 User’s Guide

204

Chapter 31 Introducing the Commands

31.9.2 Enable Mode

The following table describes the commands available for Enable mode.

help

Displays command help information.

traceroute

<ip|host-name>

Determines the path a packet takes to a device.

<ip|host-name>

[vlan <vlan-id>]

[ttl <1-255>]

[wait <1-60>]

[queries <1-10>]

Determines the path a packet takes to a device in a VLAN.

help

Displays command help information.

ssh <1|2> <[user@]dest-ip>

Connects to an SSH server with the specified SSH version.

Table 67

Command Summary: User Mode (continued)

COMMAND

DESCRIPTION

Table 68

Command Summary: Enable Mode

COMMAND

DESCRIPTION

help

Displays help information.

logout

Exits Enable (or privileged) mode.

exit

Exits Enable (or privileged) mode.

history

Displays a list of command(s) that you

have previously executed.

enable

Accesses Enable (or privileged) mode.

disable

Exits Enable (or privileged) mode.

configure

Accesses Configuration mode. See

Section 31.9.3 on page 208

logging

Disables syslog logging.

arp

Flushes the ARP (Address Resolution

Protocol) table.

interface <port-

number>

Clears the interface status of the specified

port(s).

show

Displays IP related information.

arp

Displays the ARP table.

route

Displays IP routing information.

route

static

Displays IP static route information.

hardware-monitor

<C|F>

Displays current hardware monitor

information with the specified temperature

unit (Celsius

or Fahrenheit

system-information

Displays general system information.

vlan1q

gvrp

Displays GVRP settings.

port-isolation

Displays port isolation settings.

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды