ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 210 / 282

Dimension ES-3148 User’s Guide

208

Chapter 31 Introducing the Commands

31.9.3 General Configuration Mode

The following table lists the commands in Configuration (or Config) mode.

Table 69

Command Summary: Configuration Mode

COMMAND

DESCRIPTION

help

Displays help information.

logout

Exits from the CLI.

history

Displays a list of previous

command(s) that you have

executed.

exit

Exits from the CLI.

mode zynos

Changes the CLI mode to the

ZyNOS format.

password

Change the password for

Enable mode.

Sets the management IP

address to the default value.

route <ip> <mask>

Removes a specified IP static

route.

route <ip> <mask>

inactive

Enables a specified IP static

route.

igmp-filtering

Clears the IGMP filtering

settings on the switch.

profile <name>

Deletes the IGMP filtering

profile.

profile <name>

start-address

<ip> end-address

<ip>

Deletes a rule in the IGMP

filtering profile.

igmp-snooping

Disables IGMP snooping.

mac-forward

mac <mac-addr>

vlan <vlan-id>

interface

<interface-id>

Removes the specified MAC

forwarding entry, belonging to a

VLAN group (if any) forwarded

through an interface(s).

mac <mac-addr>

vlan <vlan-id>

interface

<interface-id>

inactive

Enables the specified MAC

address, belonging to a VLAN

group (if any) forwarded through

an interface(s).

mac-filter mac

<mac-addr>

vlan <vlan-id>

inactive

Enables the specified MAC-filter

rule.

mac <mac-addr>

vlan <vlan-id>

Disables the specified MAC

filter rule.

mirror-port

Disables port mirroring on the

switch.

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды