*
Installation
Maintenance Instructions
Replacement Kits
Z7440 Series Single Handle Lavatory Faucet
With Adjustable Temperature Limit Stop
SIERRA FAUCET PARTS
ITEM
PART NO.
DESCRIPTION
QTY
1
RK7440-LH
LEVER HANDLE
1
RK7440-LH-STN LEVER HANDLE, SATIN NICKEL
1
2
RK7440-LP
LOOP HANDLE
1
RK7440-LP-STN
LOOP HANDEL, SATIN NICKEL
1
RETAINING NUT ASSY.
RK7440-3
RETAINING NUT
1
RETAINING GASKET
1
3
ESCUTCHEON
1
RETAINING NUT ASSY.
RK7440-3-STN
RETAINING NUT, SATIN NICKEL
1
RETAINING GASKET
1
ESCUTCHEON
1
4
RK7440-CART
CARTRIDGE ASSEMBLY
1
W/ LIMIT STOP
AERATOR, STD 2.2 GPM
RK7440-94
AERATOR
1
WASHER
1
AERATOR, SATIN NICKEL
1
RK7440-94-STN
STD. 2.2 GPM
AERATOR
1
WASHER
1
AERATOR SPRAY OUTLET
RK7440-94SO
1.0 GPM
AERATOR
1
WASHER
1
AERATOR, LAMINAR
FLOW, 2.2 GPM
7440-94LA
AERATOR
1
WASHER
1
5
AERATOR, VANDAL
PROOF 2.2 GPM
7440-94VP/WK
AERATOR
1
WASHER
1
KEY
1
AERATOR, VANDAL
PROOF 1.5 GPM
RK7440-94-VP1.5
AERATOR
1
WASHER
1
KEY
1
AERATOR, FLOW
CONTROL 0.5 GPM
7440-94FC/WK
AERATOR
1
WASHER
1
KEY
1
6
RK7440-90
BASE PLATE
1
MOUNTING BRACKET
ASSY.
7
RK7440-17
BRACKET
2
HEX NUT
2
8
RK7440-HK
INLET NUTS
2
SPOUT ASSY.
9
RK7440-36W
SPOUT GASKET
1
WATERWAY SPOUT
1
AERATOR WASHER
1
Form #
CF952
Date:
12/16/11
Product No.:
IS7440
C.N. No.
128418
Rev.
i
Sheet 1 of 4
ANY SIERRA FAUCETS INSTALLED PRIOR TO 3-1-05 SHOULD
ADD - OS SUFFIX TO ALL REPAIR KIT PART NUMBERS
CAUTION: DO NOT APPLY SOLDER OR BRAZE TO INLET
TUBES. EXCESSIVE HEAT MAY DAMGE COMPONENTS OF THE
SIERRA FAUCET!
3. If faucet includes pop-up or grid drain, refer to next
page for pop-up assembly installation.
4. Connect left inlet tube to hot water supply and right inlet
tube to cold water supply.
CAUTION: Care should be taken
not to kink tubes when connecting to water supplies.
1. Shut off hot and cold water supplies.
2. Place faucet base plate on faucet and position on lavatory
sink.
In some installations, a sealant may be required to
make a water tight seal between the faucet base plate and
the mounting surface. The installer should verify the
compatibility of the selected sealant with the mounting
surface manufacturer. Both plumber’s putty and silicone
sealants are compatible with Zurn faucets and fixtures.
Consult the mounting surface manufacture for their
recommendation of sealant.
From underneath the sink,
position bracket on mounting studs and attach the hex nuts.
Tighten hex nuts.
INSTALLATION INSTRUCTIONS
CONGRATULATIONS
You have purchased a ZURN Quality Manufactured lavatory fau-
cet that contains a "life of the system" ceramic cartridge. The
Sierra faucet will provide you with years of trouble free service.
If you should have any questions, please contact your local
ZURN/TEMP-GARD representative or the factory at the address
on the back of this sheet.
