background image

Zurn Industries, LLC

511 W. Freshwater Way, Milwaukee, WI U.S.A. 53204 · Ph. 1-855-ONE-ZURN, Fax 919-775-3541

In Canada

 

|

 

Zurn Industries Limited

7900 Goreway Drive Unit 10, Brampton, Ontario L6T5W6 · Ph. 905-405-8272, Fax 905-405-1292

www.zurn.com

Rev.

-

Date:

4/17/2017

C.N. No.

SAN007526

Prod. | Dwg. No.

FV617

LIMITED WARRANTY

All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from the

date of purchase. Decorative finishes warranted for one year. We will replace at no costs goods that prove defective provided we are

notified in writing of such defect and the goods are returned to us prepaid at Sanford, NC, with evidence that they have been properly

maintained and used in accordance with instructions. We shall not be responsible for any labor charges or any loss, injury or damages

whatsoever, including incidental or consequential damages. The sole and exclusive remedy shall be limited to the replacement of the

defective goods. Before installation and use, the purchaser shall determine the suitability of the product for his intended use and the

purchaser assumes all risk and liability whatever in connection therewith. Where permitted by law, the implied warranty of merchantability

is expressly excluded. If the products sold hereunder are “consumer products,” the implied warranty of merchantability is limited to a

period of three years and shall be limited solely to the replacement of the defective goods. All weights stated in our catalogs and lists are

approximate and are not guaranteed.

Serio Series

TM

Nachi Series

TM

Sensor-Operated Lavatory
Soap Dispensers

Installation, Operation, Maintenance, and
Parts Manual

NOTICE: READ ENTIRE MANUAL PRIOR TO INSTALLING PRODUCT.

NOTE: The information in this manual is subject to change at any time without notice. Installations may be performed
at different times of construction by different individuals. For this reason, these instructions should be left on-site
with the facility or maintenance manager.

Z6950-SD

Serio

®

 Series

Z6957-SD

Nachi

®

 Series

Содержание Serio Series







Отзывы: