manualshive.com logo in svg

ZURN Connected Aqua-FIT Serio Z6950-XL-S-W2, Инструкция по установке, эксплуатации, обслуживанию и каталог запасных частей

Поделиться
Скачать
ZURN Connected Aqua-FIT Serio Z6950-XL-S-W2 Скачать руководство пользователя страница 5

FV723 Rev.  B 7/29/2020

Page 4

    

Cable to 

monitor

1.  Install Monitor on wall surface within 2 feet radius of faucet  

with dry wall anchors & screws or doubled sided VHB tape

2.  Loosen lid screw with supplied 3mm Allen wrench. Open lid 

and install supplied batteries. Close lid and tighten lid screw.

5.  Tighten electronics module assembly to shank and connect 

water line(s).

3. 

Connect monitor and electronics module assembly.

Do not connect cable to the spout at this step.  

4.  Open battery module using supplied 3mm Allen wrench and 

install supplied batteries in the electronics module.  Then close 

and tighten battery module..   

Use AA Lithium Batteries or AA Alkaline batteries, but do not mix Lithium 

with Alkaline.  

Use AA Lithium Batteries or AA Alkaline batteries, but do not mix Lithium 

with Alkaline.  

Monitor & Electronic Module Installation Instructions

Содержание Connected Aqua-FIT Serio Z6950-XL-S-W2

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды