ZURN AquaSense ZER-TM Series Скачать руководство пользователя страница 9

Страница: 9 / 16

FV669 Rev. G 06/22/22

Page 8

Retrofit Installation Instruction

Figure 18A

Figure 18C

STEP 1

Turn off control stop using a flat head screw driver turning

clockwise. Then, use the electronic or manual override button or

manual handle to flush the water out of the flush valve.

STEP 2

Remove the existing valve cap/head and diaphragm kit from the

valve body to get the valve to either state shown in Figure 18A.

STEP 3

FOR ULF UNIVERSAL KIT ONLY: Loosen tailpiece nut from

control stop and slide tailpiece out of control stop. Locate

tailpiece tabs. If the valve body does not have tailpiece tabs

matching those in Figure 18B, then carefully insert the tailpiece

into the control stop, tighten the tailpiece nut, and proceed to

Step 4.

If tailpiece tabs are present, then press the Flow Restrictor into

the tailpiece, being sure to align the tabs with the pockets on the

Flow Restrictor. Carefully insert the tailpiece into the control stop

and tighten the tailpiece nut.

STEP 4

Ensure the Volume Control Ring is installed on the manifold

stem. Slide the diaphragm kit into the valve body, orienting the

orifice opposite of the control stop. See Figure 18C.

STEP 5

Install valve head and diaphragm kit onto the valve body. Rotate

the valve head so the sensor window is facing outward. See

Sensor Angle Adjustment section if more detail is needed.

STEP 6

Before tightening the locking ring, make sure the strap wrench

and locking ring are completely dry so that the strap wrench has

the best grip possible on the locking ring.

Hand tighten the locking ring onto the valve body. If the locking

ring will not thread onto the valve body go to the Locking Ring

Change Section. Finish tightening the locking ring using the strap

wrench. Turn the locking ring at least 1/3 of a turn with the strap

wrench.

STEP 7 (if applicable)

Remove the Manual Handle. Place the Handle Cap Seal in the

Handle Cap and torque the handle cap in place.

STEP 8

Slowly turn on the control stop using a flat head screw driver

turning counter-clockwise and check for leaks. If leaks occur,

tighten locking ring further. Go to Battery Installation section to

power on the unit and check for leaks once more after flushing

the valve. If you find leaks are still present. Then remove the

valve cap from the valve head shown in Step 4.1 & 4.2 of the

Battery Installation Section. Use the supplied strap wrench or a

large wrench on the flats of the locking ring to tighten it.

Mating Pockets (X2)

Tailpiece Tabs (X2)

Figure 18B

Orifice

Volume

Control Ring

Manifold Stem

Содержание AquaSense ZER-TM Series

















Результаты поиска

Содержание AquaSense ZER-TM Series

Отзывы:

Похожие инструкции для AquaSense ZER-TM Series

Бренды по названию

Популярные бренды

ZURN AquaSense ZER-TM Series, Инструкция по установке, эксплуатации, обслуживанию и каталог запасных частей

Результаты поиска

Содержание AquaSense ZER-TM Series

Отзывы:

Похожие инструкции для AquaSense ZER-TM Series

Бренды по названию

Популярные бренды