Zultys MX250 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 62

background image

5. Mounting the MX250

29

4.

Fasten a mounting bracket using two M4x6 screws (58-20002-00) at positions A and B (front

side) or positions C and D (middle of the front side or middle of the rear side installation).
For a rear side installation, fasten the mounting and plastic bracket using two M4x10 screws

(58-2005-00) at positions A and B.

Warning

Use only the M4x10 screws (58-20005-00) to secure the plastic bracket and

mounting bracket for a rear side installation. Use only M4x6 screws (58-20002-00)

to secure the mounting bracket for all other installation configurations. Using a

longer length screw may protrude too far into the chassis and damage the internal

boards. Using a shorter length screw may not securely fasten the mounting bracket

to the chassis and cause the chassis to fall after mounting to the equipment rack.

5.

Repeat step 2 through step 4 for the other side of the chassis.

5.6

Installing the Chassis into the Equipment Rack

1.

Ensure that the two mounting brackets have been fastened to the chassis as described in

section 5.5 on page 27.

2.

Hold the main chassis in place on a 19

"

equipment rack, with the flanges of the mounting

brackets aligned against the holes in the front of the rack.

Warning

You need two people to lift and install the MX250. Grasp the chassis underneath

the lower edge and lift with both hands. To prevent injury, keep your back straight

and lift with your legs, not your back.

3.

While holding the chassis in place, use a hand screwdriver to screw the four 12-24 mounting

screws into place on the flanges.

1

Do not tighten the screws.

4.

Once mounted in position with the screws in place, use a power screwdriver to tighten all

four screws.

1. The MX250 is supplied with four 12-24 mounting (imperial) screws and M6x10 mounting (metric) screws for conven-

tional 19” equipment racks. Use either the 12-24 mounting screws or the M6x10 mounting screws, depending on the

thread pattern of equipment rack.

«
...
31
32
33
34
35
...
»

Содержание MX250































































Отзывы:

Нет отзывов

Похожие инструкции для MX250

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 10

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 57

Бренд: 3Com Страницы: 2

Opal Series 2006

Бренд: Teledex Страницы: 4

D1780-2BT Series

Бренд: Uniden Страницы: 28

Бренд: Steren Страницы: 19

FortiVoice 50E6

Бренд: Fortinet Страницы: 22

Бренд: Topcom Страницы: 72

Бренд: AT&T Страницы: 21

Бренд: Logik Страницы: 16

Бренд: Plantronics Страницы: 2

Бренд: Ipevo Страницы: 4

Бренд: RAYTAC Страницы: 20

Voice Terminal 8510T

Бренд: AT&T Страницы: 29

Бренд: Yealink Страницы: 56

Бренд: Inter-Tel Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды