Zultys MX250 Скачать руководство пользователя страница 20

Страница: 20 / 62

MX250 Hardware Manual

3.4.3.2

PCM RJ45 Pin Assignments

Each circuit on the PCM card terminates on an RJ45 connector. Figure 3-8 shows the pin

placement of each pin of the PCM. Both circuits have the same pin assignment. Figure 3-9 shows

the function assignment of each pin.

Figure 3-10 displays the connection of PCM circuits to the network or other equipment. Use a

straight cable to connect the MX250 to the network jack. Use a crossover cable to connect the

MX250 to an existing terminal system (such as an existing PBX). Figure 3-10 also displays MX250

pinouts and pinouts typically used for terminal and network equipment. Consult the

documentation for specific devices to confirm the pin assignment.

Figure 3-8

Pin Assignment of PCM Circuits on PCM Card

Pin

Signal Name

Circuit

Source

common

Received Data, ring

BAa

Facility

Received Data, tip

BAb

Facility

Transmitted Data, ring

BBa

MX250

Transmitted Data, tip

BBb

MX250

Figure 3-9

Pin Description of a PCM Circuit

Figure 3-10

Wiring the PCM Circuits to the Network or Other Equipment

Содержание MX250































































Результаты поиска

Содержание MX250

Отзывы:

Похожие инструкции для MX250

Бренды по названию

Популярные бренды

Zultys MX250, Руководство по оборудованию

Результаты поиска

Содержание MX250

Отзывы:

Похожие инструкции для MX250

Бренды по названию

Популярные бренды